Cisco Systems manual 42Cisco IGX 8400 Series Installation and Configuration

Page 42

Attaching Peripherals

Step 6 After the workstation and IGX node interface have been set up, Cisco WAN Manager can be started. After Cisco WAN Manager has started and the communication sockets are active, the dsplan screen looks like this:

D2.cb1	LAN cisco IGX 8410	9.3 Feb. 27 2000 14:27 PST
Active IP Address:		192.187.207.21
IP Subnet Mask:		255.255.255.0
TCP Service	Port:	5130
Default Gateway IP Address:		192.187.207.1
Maximum LAN	Transmit Unit:	1500
Ethernet Address:		00.55.43.00.04.55
Control Socket - Ready
Base Socket	Descriptor - 1
Open Socket	Descriptor - 2

Last Command: dsplan

Next Command:

Note “Sockets” is the BSD UNIX name for connections between processes and typically applies to network communication.

Note Before switching on the Cisco WAN Manager workstation, refer to the Cisco WAN Manager Operations publication.

3-42Cisco IGX 8400 Series Installation and Configuration

Image 42

Contents Card Installation and Node Startup Preparing the CardsPreparing the Cards IGX 8410 Cards, Front View IGX 8410 Cards, Back View IGX 8420 Card Shelf, Front View IGX 8430 Back View Inserting the Cards Inserting ModulesMaking Signal Connections HssiConnecting Trunks Setting Up a UXM-EBringing Up a UXM-E Trunk Cable Management Inverse Multiplexing over ATM on Trunks DspcdsAdding an IMA Feeder Trunk Adding Links to an IMA Feeder GroupUXM-E Inverse Multiplexing ATM IMA Lines Removing Links from an IMA Feeder GroupConnecting an NTM T1 or Y1 Trunk Connecting an NTM E1 or Subrate TrunkBringing Up a UXM-E in UNI or NNI Port Mode Installing Voice Cards Connecting a CVM to a T1 or J1 LineConnecting a CVM to an E1 Line or a Subrate Trunk TDM Transport on the CVMConnecting a UVM to T1 Lines Pass-Through and Standard External UVM T1 Cabling Connecting a UVM to E1 Lines Pass-Through and Standard External UVM E1 Cabling Connecting a UVM to J1 Lines 10 Pass-Through and Standard External UVM J1 Cabling Making Serial Data Connections 11 SDI and LDI FaceplatesConﬁguring the Port Modes of the HDM Back Cards Conﬁguring the Mode of an LDI Port HDM and LDM Redundancy13 Connecting a DTE or DCE Adapter Cable to an LDI Making Frame Relay Connections Maximum Connections Per Port with Signalling ProtocolsSetting Up Frame Relay on a UFM Cable Redundancy on the UFMs14 Y-Cable Redundancy with Single and Dual-Port Cabling Connecting UFM Cabling Setting Up Frame Relay Ports and Connections UFMSetting Up Frame Relay on an FRM Commands for T1/E1 Frame RelayDeleting a Frame Relay Port Port Mode Selection for V.35 15 Setting the Port Mode DTE/DCE on an FRI Frame Relay Card RedundancySetting Up Frame Relay Ports and Connections FRM Making Alarm Relay Output Connections 36Cisco IGX 8400 Series Installation and Configuration Connecting a Single Network Management Station Making External Clock ConnectionsAttaching Peripherals 16 Connecting the Control Terminal LAN Connection for the Network Management Station 17 LAN Connection to SCMConﬁguring the LAN Port D2.cb1 LAN superuser IGX 42Cisco IGX 8400 Series Installation and Configuration Connecting a Network Management Station to Multiple Networks Connecting the Printer 20 Connecting a Network PrinterConnecting a Modem 21 Connecting Modems to an IGX NodeConnecting the Power Supply Monitor Initial Startup of the IGXNPM Startup Diagnostic Test Fail screen looks like thisCard Self Test Inspecting Status LightsChecking the Power Supplies AC Systems IGX Conﬁguration Summary50Cisco IGX 8400 Series Installation and Configuration Conﬁguring an IGX Switch to Be an Interface Shelf Interworking Connections in a Tiered NetworkAdding Connections in a Tiered Network through the CLI Converting a Routing Node to an Interface Shelf