Cisco Systems IE 3010 manual Dual-Purpose Ports

Page 12

Chapter 1 Product Overview

Cable Side

The 10/100 PoE ports on the Cisco IE-3010-16S-8PC switches provide PoE support for devices that are compliant with IEEE 802.3af. The Cisco prestandard PoE is also supported for Cisco IP Phones and Cisco Aironet Access Points. The PoE ports on the switch deliver up to 15.4 W of PoE. Any four of the eight ports are designated as high priority PoE ports, while the other four ports are designated as low priority PoE ports. When both the power-supply modules are installed, the system has enough power to support all eight ports as PoE ports. In case one of the power-supply modules fails, the power to the low priority PoE ports is dropped, while power to the high priority PoE ports remains uninterrupted.

On a per-port basis, you control whether or not a port automatically provides power when an IP phone or an access point is connected.

The 10/100 PoE ports use RJ-45 connectors with Ethernet pinouts. The maximum cable length is 328 feet (100 meters). The 100BASE-TX and 1000BASE-T traffic requires Category 5, Category 5e, or Category 6 unshielded twisted pair (UTP) cable. The 10BASE-T traffic can use Category 3 or Category 4 UTP cable.

For information about configuring and monitoring PoE ports, see the switch software configuration guide on Cisco.com.

For information about port connections and port specifications, see the “Connecting Devices to the Ethernet Ports” section on page 2-25and the “Connector and Cable Specifications” section on page B-1.

Note The output of the PoE circuit has been evaluated as a Limited Power Source (LPS) per IEC 60950-1.

Dual-Purpose Ports

You can configure the dual-purpose ports on the switch as either 10/100/1000 ports or as SFP-module ports. You can set the 10/100/1000 ports to autonegotiate, or you can configure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet ports.

By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP-module port has priority, but you can use the media-typeinterface configuration command to manually designate the port as an RJ-45 port or an SFP port.

You can configure the speed and duplex settings consistent with the selected media type. For information on configuring interfaces, see the switch software configuration guide.

Cisco IE 3010 Switch Hardware Installation Guide

1-4

78-19581-02

 

 

Image 12
Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelPower-Input Terminal Alarm PortsSFP Module Patch Cable Alarm Input Alarm OutputManagement Ports Switch Panel LEDs LEDsPower-Supply Module LEDs Alarm LEDsSystem LED Color System StatusConsole LEDs Port LEDsColor Description LED Color MeaningSD Flash Memory Card PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDPower Supply Features Network ConfigurationsManagement Options Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesInstalling a Power-Supply Module Grounding the SwitchEquipment That You Need Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Switch Specifications Physical SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6