Cisco Systems IE 3010 manual Management Ports, Alarm Input, Alarm Output

Page 15

Chapter 1 Product Overview

Cable Side

Alarm Input

The alarm input is a dry-contact alarm port. You can connect up to four alarm inputs from devices, such as a door, a temperature gauge, or a fire alarm, to the alarm port. You can use the CLI to set the alarm severity to minor, major, or critical. An alarm generates a system message and turns on an LED. See the “Alarm LEDs” section on page 1-9for the LED descriptions.

Alarm Output

The alarm output can be configured as a minor or major alarm. Output alarms often control an external alarm, such as a bell or a light. To connect an external alarm device to the relay, you connect two relay contact wires to complete the electrical circuit. See Figure B-4 on page B-3for information on the alarm pinouts.

Management Ports

You can connect the switch to a PC running Microsoft Windows or to a terminal server through either the RJ-45 console port or the USB console port.

•RJ-45 console port. The RJ-45 connection uses an RJ-45-to-DB-9 female cable.

•USB mini-Type B console port (5-pin connector). The USB connection uses a USB Type A-to-5-pin mini-Type B cable.

The USB console interface speeds are the same as the RJ-45 console interface speeds.

To use the USB console port, you must install the Cisco Windows USB device driver on the device that is connected to the USB console port (device running with Microsoft Windows).

Note For information about downloading the Cisco USB device driver, see the “Installing the Cisco Microsoft Windows USB Device Drivers” section on page C-4.

With the Cisco Windows USB device driver, connecting and disconnecting the USB cable from the console port does not affect Windows HyperTerminal operations. Mac OS X or Linux require no special drivers.

Note The 5-pin mini-Type B connectors resemble the 4-pin mini-Type B connectors. They are not compatible. Use only the 5-pin mini-Type B. See Figure 1-5.

Figure 1-5 USB Mini-Type B Port

253163

The configurable inactivity timeout reactivates the RJ-45 console port if the USB console port is activated, but no input activity occurs on it for a specified time period. When the USB console port deactivates due to a timeout, you can restore its operation by disconnecting and reconnecting the USB cable. For information on using the CLI to configure the USB console interface, see the switch software guide.

Cisco IE 3010 Switch Hardware Installation Guide

 

78-19581-02

1-7

 

 

 

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Americas Headquarters Cisco IE 3010 Switch Hardware Installation GuidePage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Related Publications Obtaining Documentation and Submitting a Service RequestModel Description Switch ModelsCisco IE-3010-24TC Cable-Side View Cable SidePoE Ports 10/100 Fast Ethernet PortsDual-Purpose Ports Type of SFP Module Model SFP ModulesPower-Input Terminal Alarm PortsSFP Module Patch Cable Alarm Input Alarm OutputManagement Ports LEDs Switch Panel LEDsColor System Status Power-Supply Module LEDsAlarm LEDs System LEDLED Color Meaning Console LEDsPort LEDs Color DescriptionSD Flash Memory Card LED SD Flash Memory CardPoE LED Dual-Purpose Port LEDsPSU OK LED Power-Supply SideUSB LED Power-Supply Side LEDsPower Supply Features Network ConfigurationsManagement Options Switch Installation 75 in .4 cm. Statement Verifying Switch Operation Installation GuidelinesRack-Mounting Installing the SwitchAttaching Brackets for 19-Inch Racks 1and -2show how to attach brackets to the switches207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching 23-Inch Brackets Attaching Brackets for 23-Inch RacksAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets for IP-30 Compliance Optional Attaching BracketsRubber plug Switch-side User-supplied screws Wall-Mounting the Switch15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing SFP Modules Installing and Removing SFP ModulesRemoving SFP Modules Inserting and Removing the SFP Module Patch Cable18 Inserting an SFP Module Patch Cable Removing the SFP Module Patch Cable20 Loosening the Captive Screw Replacing the SD Flash Memory Card22 Removing the SD Flash Memory Card Connecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsDevice Crossover Cable Connecting to the 10/100 PoE PortsWhere to Go Next Page Power-Supply Modules Power Supply InstallationPower-supply module 3 Captive screw Installation Guidelines Power-Supply Module InstallationInstalling a Power-Supply Module Grounding the SwitchEquipment That You Need Stripping the Ground Wire Crimping the Terminal Lug Installing the Power-Supply Module in the SwitchLoosen the Screws on the Power Supply Blank Wiring the Power SourceAC 5 A, DC 15 a Statement Opening the Power-Input Terminal Cover100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 AC power Removing the Power-Supply Module16 Removing the Power-Supply Module Page Switch Post Results Diagnosing ProblemsEthernet and Fiber-Optic Cables Switch LEDsSwitch Connections Bad or Damaged CableSFP Module Interface Settings10/100 and 10/100/1000 Port Connections 10/100 PoE Port ConnectionsAutonegotiation and Network Interface Cards Switch PerformanceSpanning Tree Loops Speed, Duplex, and AutonegotiationFinding the Switch Serial Number Resetting the Switch to the Factory Default SettingsSerial Number Location for the Power-Supply Modules Switch Specifications Physical SpecificationsEnvironmental Ranges Power Requirements Power Requirements Power Specifications Power-Supply Module SpecificationsAlarm Ratings Page 10/100 Connector SpecificationsFigure B-2 Fiber-Optic SFP Module LC Connector SFP Module ConnectorsPin Alarm connection Alarm PortSFP Module Cables Cables and AdaptersGLC-EX-SMD Extended temperature SFPsTP3 Cable PinoutsDSR DTR CTS RTS Console Port Adapter PinoutsSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB Console Port Figure C-2 Connecting the USB Console CableInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows Vista USB Driver Uninstalling the Cisco Microsoft Windows USB DriversUsing the Setup.exe Program Uninstalling the Cisco Microsoft Windows Vista USB DriverEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6
Top Page Image Contents