Cisco Systems IE 3010 manual Cables and Adapters, SFP Module Cables

Page 80

Appendix B Connector and Cable Specifications

Cables and Adapters

Cables and Adapters

•SFP Module Cables, page B-4

•Cable Pinouts, page B-6

•Console Port Adapter Pinouts, page B-7

SFP Module Cables

Each port must match the wave-length specifications on each end of the cable, and for reliable communications, the cable must not exceed the allowable length. Copper 1000BASE-T SFP transceivers use standard four twisted-pair, Category 5 (or greater) cable at lengths up to 328 feet (100 meters).

Note The maximum operating temperature of the switch varies depending on the type of SFP module that you use. See Table 1-2 on page 1-5for information on the supported temperature ranges.

Table B-1				Fiber-Optic SFP Module Port Cabling Specifications

							Core	Modal
					Wavelength		Size/Cladding	Bandwidth
	Type of SFP Module				(nanometers)	Fiber Type	Size (micron)	(MHz/km)1	Cable Distance
	Industrial and Rugged SFPs

	1000BASE-SX				850	MMF	62.5/125	160	722 feet (220 m)
	(GLC-SX-MM-RGD)						62.5/125	200	902 feet (275 m)
							50/125	400	1640 feet (500 m)
							50/125	500	1804 feet (550 m)

	1000BASE-LX/LH				1310	SMF	G.6522	—	32,810 feet (10 km)
	(GLC-LX-MM-RGD)

	100BASE-LX				1310	SMF	G.6522	—	32,810 feet (10 km)
	(GLC-FE-100LX-RGD)

	100BASE-FX				1310	MMF	50/125	500	6,562 feet (2 km)
	(GLC-FE-100FX-RGD)						62.5/125	500	6,562 feet (2 km)

	1000BASE-ZX				1550	SMF	G.6522	—	43.4 to 62 miles
	(GLC-ZX-SM-RGD)								(70 to 100 km)2
	Commercial SFPs

	1000BASE-BX10-D				1490 TX	SMF	G.6523	—	32,810 feet (10 km)
	(GLC-BX-D)				1310 RX

	100BASE-LX				1310	SMF	G.6522	—	32,810 feet (10 km)
	(GLC-FE-100LX)

	100BASE-BX				1310 TX	SMF	G.6522	—	32,810 feet (10 km)
	(GLC-FE-100BX-D				1550 RX
	GLC-FE-100BX-U)

	100BASE-FX				1310	MMF	50/125	500	6,562 feet (2 km)
	(GLC-FE-100FX)						62.5/125	500	6,562 feet (2 km)

			Cisco IE 3010 Switch Hardware Installation Guide
			Cisco IE 3010 Switch Hardware Installation Guide

	B-4								78-19581-02
	B-4								78-19581-02

Image 80

Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelSFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output Switch Panel LEDs LEDsPower-Supply Module LEDs Alarm LEDsSystem LED Color System StatusConsole LEDs Port LEDsColor Description LED Color MeaningSD Flash Memory Card PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6