Cisco Systems IE 3010 manual Power-Input Terminal, Alarm Ports, SFP Module Patch Cable

Page 14

Chapter 1 Product Overview

Cable Side

SFP Module Patch Cable

The switch uses an SFP-module patch cable, a 0.5-meter, copper, passive cable with SFP module connectors at each end (see Figure 1-3). The patch cable connects two switches in a cascaded configuration.

Figure 1-3 SFP-Module Patch Cable

126809

See the “Inserting and Removing the SFP Module Patch Cable” section on page 2-21for information about using the SFP module patch cable.

You can order this cable (part number CAB-SFP-50CM=).

Power-Input Terminal

The power-input terminal provides screw terminals for the AC and DC power connections. The switch can operate with one or two power supplies. If one of the power sources fail, the other continues to power the switch. See Chapter 3, “Power Supply Installation,” for information.

Figure 1-4 Power-Input Terminal

208415

Alarm Ports

The switch has four alarm inputs and one alarm output. The alarm setting is open or closed.

•Open means that the normal condition has current flowing through the contact (referred to as a normally closed contact). The alarm is generated when the current stops.

•Closed means that no current flows through the contact (referred to as a normally open contact). The alarm is generated when the current flows.

Cisco IE 3010 Switch Hardware Installation Guide

1-6	78-19581-02

Image 14

Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelSFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output Switch Panel LEDs LEDsSystem LED Power-Supply Module LEDsAlarm LEDs Color System StatusColor Description Console LEDsPort LEDs LED Color MeaningDual-Purpose Port LEDs SD Flash Memory CardPoE LED SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber-Optic Cables10/100 PoE Port Connections Interface Settings10/100 and 10/100/1000 Port Connections SFP ModuleSpeed, Duplex, and Autonegotiation Switch PerformanceSpanning Tree Loops Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6