Cisco Systems IE 3010 Removing the SFP Module Patch Cable, Inserting an SFP Module Patch Cable

Page 44

Chapter 2 Switch Installation

Inserting and Removing the SFP Module Patch Cable

Figure 2-18 Inserting an SFP Module Patch Cable

Cisco IE 3010

208372

Step 3 Repeat these steps for the second switch that you want to connect to the first switch.

Figure 2-19 Connecting Two Switches with an SFP Module Patch Cable

PO W	OVER
ER	OVER
	ETHERNET
PO W ER	ERNET
	ERNET
	Cisco
	IE 3010
PO W	OVER
ER	OVER
	ETHERNET
PO W	OVER
ER	OVER
	ETHERNET
	Cisco
	IE 3010

208373

Removing the SFP Module Patch Cable

To remove an SFP module patch cable from the SFP module slot, release the connector, and pull it from the slot.

Cisco IE 3010 Switch Hardware Installation Guide

2-22	78-19581-02

Image 44

Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelSFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output Switch Panel LEDs LEDsPower-Supply Module LEDs Alarm LEDsSystem LED Color System StatusConsole LEDs Port LEDsColor Description LED Color MeaningSD Flash Memory Card PoE LEDDual-Purpose Port LEDs SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6