Cisco Systems IE 3010 manual Removing the Power-Supply Module, AC power

Page 62

Chapter 3 Power Supply Installation

Removing the Power-Supply Module

Step 8 Torque the captive screws (above the wires) to 8.5 in-lb (± 0.5 in-lb).

Step 9 AC power

Connect the other end of the line wire (the one connected to L) to the line terminal on the AC-power source, and connect the other end of the neutral wire (the one connected to N) to the neutral terminal on the AC power source.

DC power

Connect the other end of the positive wire (the one connected to +) to the positive terminal on the DC-power source, and connect the other end of the negative wire (the one connected

to ) to the negative terminal on the DC power source.

Step 10 Close the power-input terminal cover. Use a ratcheting torque screwdriver to torque the screw to 6–8 in-lb.

Step 11 Turn on the power at the AC or DC circuit, verify that the PSU1 or PSU2 LED on the switch and PSU OK LED on the power-supply module are green.

Step 12 If you have two power supplies, repeat Step 1 through Step 11. See the switch software guide for information on how to configure the power supply settings.

Removing the Power-Supply Module

The power-supply modules are hot-swappable. By removing the power-supply modules, you can power off the switch without disconnecting the wiring from the power-input terminal.

Step 1 We recommend that power be OFF at the AC or DC circuits. Locate the circuit breakers, turn them OFF and tape them in the OFF position.

Note If the power is not off at the AC or DC circuit breaker, do not touch the power-input terminal.

Step 2 Verify that the PSU LED and PSU OK LED is blinking red or is off.

Step 3 Use a Phillips screwdriver to loosen the captive screws that secure the power-supply module to the switch. See Figure 3-15.

Warning Hot surface. Statement 1079

Figure 3-15 Removing the Screws

Cisco IE

3010

Sw

 

 

itch Series

208384

 

Cisco IE 3010 Switch Hardware Installation Guide

3-12

78-19581-02

Image 62
Contents Cisco IE 3010 Switch Hardware Installation Guide Americas HeadquartersPage N T E N T S Wall-Mounting2-15 Power-Supply Module Specifications A-4 Accessing the CLI Through the Console Port C-1 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Model DescriptionCable Side Cisco IE-3010-24TC Cable-Side View10/100 Fast Ethernet Ports PoE PortsDual-Purpose Ports SFP Modules Type of SFP Module ModelSFP Module Patch Cable Power-Input TerminalAlarm Ports Management Ports Alarm InputAlarm Output Switch Panel LEDs LEDsSystem LED Power-Supply Module LEDsAlarm LEDs Color System StatusColor Description Console LEDsPort LEDs LED Color MeaningDual-Purpose Port LEDs SD Flash Memory CardPoE LED SD Flash Memory Card LEDPower-Supply Side PSU OK LEDPower-Supply Side LEDs USB LEDManagement Options Power Supply FeaturesNetwork Configurations Switch Installation 75 in .4 cm. Statement Installation Guidelines Verifying Switch OperationInstalling the Switch Rack-Mounting1and -2show how to attach brackets to the switches Attaching Brackets for 19-Inch Racks207231 Rubber plug Switch Inserting the Rubber Plugs 255740 255750 255751 Attaching Brackets for 23-Inch Racks Attaching 23-Inch BracketsAttaching Brackets for Etsi Racks Attaching Brackets for Etsi RacksRack-Mounting the Switch Wall-Mounting Attaching Brackets Attaching Brackets for IP-30 Compliance OptionalRubber plug Switch-side Wall-Mounting the Switch User-supplied screws15 Wall-Mounting the Cisco IE-3010-16S-8PC Installing and Removing SFP Modules Installing SFP ModulesInserting and Removing the SFP Module Patch Cable Removing SFP ModulesRemoving the SFP Module Patch Cable 18 Inserting an SFP Module Patch CableReplacing the SD Flash Memory Card 20 Loosening the Captive Screw22 Removing the SD Flash Memory Card Connecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsConnecting to the 10/100 PoE Ports Device Crossover CableWhere to Go Next Page Power Supply Installation Power-Supply ModulesPower-supply module 3 Captive screw Power-Supply Module Installation Installation GuidelinesEquipment That You Need Installing a Power-Supply ModuleGrounding the Switch Stripping the Ground Wire Installing the Power-Supply Module in the Switch Crimping the Terminal LugWiring the Power Source Loosen the Screws on the Power Supply BlankOpening the Power-Input Terminal Cover AC 5 A, DC 15 a Statement100-240V~, 50-60Hz, 2A 10A 10A 11 Stripping the Input Power Source Wire 13 Connecting the Wires to the High-Voltage AC Power PSU1 Removing the Power-Supply Module AC power16 Removing the Power-Supply Module Page Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber-Optic Cables10/100 PoE Port Connections Interface Settings10/100 and 10/100/1000 Port Connections SFP ModuleSpeed, Duplex, and Autonegotiation Switch PerformanceSpanning Tree Loops Autonegotiation and Network Interface CardsResetting the Switch to the Factory Default Settings Finding the Switch Serial NumberSerial Number Location for the Power-Supply Modules Environmental Ranges Switch SpecificationsPhysical Specifications Power Requirements Power Requirements Power-Supply Module Specifications Power SpecificationsAlarm Ratings Page Connector Specifications 10/100SFP Module Connectors Figure B-2 Fiber-Optic SFP Module LC ConnectorAlarm Port Pin Alarm connectionCables and Adapters SFP Module CablesExtended temperature SFPs GLC-EX-SMDCable Pinouts TP3Console Port Adapter Pinouts DSR DTR CTS RTSSwitch Console RJ-45-to-DB-25 Port DTE Adapter Device Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB Console Cable USB Console PortInstalling the Cisco Microsoft Windows 2000 USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows XP USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Installing the Cisco Microsoft Windows Vista USB DriverUninstalling the Cisco Microsoft Windows Vista USB Driver Using the Setup.exe ProgramCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter virtual terminal password terminal-password These choices appear Cisco IE 3010 Switch Hardware Installation Guide Numerics IN-2 IN-3 IN-4 IN-5 IN-6