Cisco Systems SFS 3012 manual Viii

Page 8

viii

CAUTION: Grounding is supplied by the ground-prong on the 3-prong power cable. Do not attach a separate ground cable. Do not use adapter plugs. Do not remove the ground prong from the cable. Ensure the ground connection on the power supply is correct and functioning before applying power to the Topspin 360.

CAUTION: Always ground yourself before touching any internal Topspin 360 component to avoid damage from electrostatic discharge (ESD).

CAUTION: The Topspin 360 has two power cables. The operator must disconnect all power cables before attempting to remove the Topspin 360 from the rack.

CAUTION: Remove power cables by grasping the cable connector and pulling straight out.If the chassis comes equipped with a power-plug retainer, move the bail wire used to retain the plug to the side before attempting to remove the power plug. To replace power-supply cables, grasp the cable connector, align the connector with the power jack, and insert the connector straight into the jack. If the chassis comes equipped with a power-plug retainer, move the bail wire back into place to keep the power plug firmly in place.

CAUTION: The Topspin 360 contains lithium batteries. Do not attempt to replace or discard these batteries. The batteries may only be serviced by Topspin service personnel.

CAUTION: Observe and follow service markings. Do not service the Topspin 360, except as explained in the Topspin documentation supplied with your Topspin 360. Opening the chassis or removing the enclosure cover exposes you to electrical shock and may damage Topspin 360 components.

If one or more of the following situations occurs, remove power to the Topspin 360 and contact your

Topspin support representative:

•The power cable or power plug is damaged.

•The Topspin 360 has been exposed to water.

•The Topspin 360 has been dropped or damaged in any way.

•The Topspin 360 does not operate correctly after following the installation instructions.

CAUTION: You must ensure the operating environment has adequate air circulation. Keep the Topspin 360 in a cool, well-ventilated room. Do not block cooling vents. Install filler panels into all unused slots.

Image 8

Contents Part Number OL-7722-01 Product ID Page Contents Regulatory Notices Vii Install and Boot the Topspin Specifications and Compliance Page Electrical Cautions FCC Statement Safety InformationRegulatory Notices Viii General Cautions Laser CautionsContact Information Laser SpecsProduct Registration Thank YOU for Purchasing Your Topspin ProductXii Standard Product Agreement Xiv Page Xvi Xvii Xviii Topspin 360 Overview IntroductionFeatures PerformanceUnified Fabric Transparent TopologyRedundancy and High-Availability ScalabilityPage Topspin 360 Components Install a Controller Card Controller Cards2Inserting the Controller Card 3Closing the Ejector Lever Ethernet and Fibre Channel Gateways Replacing and Updating Your GatewaysInfiniBand Switch Cards Install an Ethernet or Fibre Channel GatewayInstall InfiniBand Switch Cards 7Inserting a Switch Card8Closing Switch Ejector Levers Power Supply Modules Remove InfiniBand Switch CardsInstall Power Supply Modules 10Power Supply ModulesBlower Trays Removing a Power SupplyInstall Blower Trays Removing Blower Trays Page Page Install and Boot the Topspin Prepare the Site for the TopspinInstall Topspin 360 Components Rack the TopspinRead the Cautionary Statements Prepare the Physical Environment for Topspin1Positioning the Side Flanges 3Rail Positioning 4Attaching Rails from the Front 5Attaching Rails from the Back 6Positioning the Chassis on the Rails Attach a Serial Console Cable to a PC or Terminal 8Securing the Chassis to the RailsBoot your Topspin 360 and Configure Basic Connectivity Assign a Static IP AddressEnter the interface mgmt-ethernet command Obtain an IP Address with DhcpConnect InfiniBand Hosts 9Fully Installed IB Cable with Pinch Connector 11Removing a Pinch Connector 12Removing a Pull Connector Manage the TopspinViewing and Updating the Software Image on the Chassis View the Software Image Version with the CLIAn installed image file will have a slash / in the name View the Software Image Version with the GUIUpgrade the Software Image with the CLI 14View Current Image of an Individual CardUpgrade the Software Image with the GUI 15Copy an Image File to the Switch 16Specify the Boot Configuration Delete an Image with the CLISelect Maintenance File Management Delete an Image with the GUIPage Topspin 360 Field Replaceable Units Expansion ModulesInstalling an InfiniBand Switch Card Configuring a New InfiniBand Switch CardUpdate the switch card firmware. Enter the install command Installing a Power Supply Power ModulesRemoving an InfiniBand Switch Card 2Power Supply Module Positioning Installing a Blower Tray Replacing Blower TraysRemoving a Blower Tray Page Topspin 360 LEDs Topspin 360 System LED Activity IndicationPower Supply LEDs 1Power Supply LEDsBlower Tray LEDs 2Blower Tray LEDsController Card LEDs LED State IndicationIB Switch Card LEDs IB Port LEDsFibre Channel Gateway LEDs FC Port LEDsEthernet Gateway LEDs Ethernet Port LEDsSpecifications and Compliance General SpecificationsLaser Specs Electrical SpecificationsCertifications/Regulatory Topspin P/N Application Optical Parameters Page Index

Related manuals

Manual 28 pages 17.41 Kb