Cisco Systems 3560-C manual Switch Installation, Preparing for Installation

Page 27

C H A P T E R 2

Switch Installation

This chapter describes how to start your switch and how to interpret the power-on self-test (POST) that ensures proper operation. It also describes how to install the switch.

Read the topics and perform the procedures in this order:

•Preparing for Installation, page 2-1

•Verifying Switch Operation, page 2-5

•Mounting the Switch, page 2-5

•Installing a Cover for the Reset Button (Optional), page 2-24

•Installing the Power Cord Retainer (Optional), page 2-25

•Installing the Cable Guard (Optional), page 2-28

•Connecting Devices to the Ethernet Ports, page 2-33

Preparing for Installation

•Warnings, page 2-1

•Installation Guidelines, page 2-3

•Equipment That You Supply, page 2-4

•Box Contents, page 2-4

•Powering the Switch, page 2-4

Warnings

These warnings are translated into several languages in the Regulatory Compliance and Safety Information for the Catalyst 3560-C and the 2960-C Switches guide.

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals. Statement 43

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

	OL-23803-02	2-1

Image 27

Contents Text Part Number OL-23803-02 Americas HeadquartersPage N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Related Publications Obtaining Documentation and Submitting a Service RequestSwitch Model Description Switch ModelsFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View 10/100 and 10/100/1000 Fast Ethernet Downlink Ports PoE Ports Switches with PoE PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D= USB Type a PortDual-Purpose Ports SFP ModulesUSB Mini-Type B Port Management PortsLEDs Switch Panel LEDsColor Description System LEDConsole LEDs Color System StatusPort LEDs Port Mode DescriptionPort status Port status. This is the default mode Modes for Port LEDsPoE LED Dual-Purpose Port LEDsColor Meaning Rear Panel Security slot Power adapter connector Reset buttonInternal Power Supply Auxiliary Power AdapterAuxiliary power adapter Reset Button Management OptionsSecurity Slots Cisco IOS CLI Network ConfigurationsPreparing for Installation Switch InstallationStatement Installation Guidelines Powering the Switch Box ContentsEquipment That You Supply Mounting the Switch Verifying Switch OperationOn a Desk or Shelf without Mounting Screws Desk, Shelf, or Wall with Mounting ScrewsDesk- or Shelf-Mounting Installing the Mounting Screws on Top of a Desk or a Shelf Under the Desk- or Shelf-Mounting Mounting the Switch on Top of a Desk or ShelfDesk or shelf Screws Screw template Adhesive Installing the Mounting Screws Under a Desk or ShelfDesk or shelf Slides on this way Wall-MountingLocation of the Mounting Holes on the Switch 77 in .49 cm 72 in .44 cm 46. 62 in .19 cm SwitchInstalling the Mounting Screws on the Wall Mounting Tray with Screws With a Mounting TrayInstalling the Switch on the Mounting Tray Switch Mounting tray Sliding direction DeskMounting Tray with a Magnet Switch Number-10 Phillips pan-head screws11 Placing the Switch on the Mounting Tray Place the switch on the mounting tray. See Figure13 Wall-Mounting with a Magnet Attaching Brackets to the Switch A RackPhillips flat-head screw 15 Attaching the 23-inch Brackets for Rack-Mounting Mounting the Switch in a RackOn a DIN Rail Attaching the DIN-Mount Tray to the SwitchPlace the switch on the DIN rail mount. See Figure Switch DIN rail mount18 Securing the DIN-Mount Tray to the Switch Mounting the Switch on a DIN Rail19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Switch Reset button cover Installing a Cover for the Reset Button Optional23 Inserting the Retainer through the Lanced Loop Installing the Power Cord Retainer OptionalSlide the retainer through the first latch. See Figure AC power cord Latches Sleeve for thin power cords26 Sleeve Around the Power Cord Washer Installing the Cable Guard Optional29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch After Installing the Switch Installing SFP ModulesNumber-8 Phillips wood screws Desk or shelf Grasp the SFP module, and carefully remove it from the slot Removing SFP ModulesTX and which is receive RX Insert a dust plug into the optical ports of the SFP moduleConnecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsBale clasp Device Crossover Cable Connecting to the PoE PortsWhere to Go Next OL-23803-02 Switch Post Results Diagnosing ProblemsEthernet and Fiber-Optic Cables Switch LEDsSwitch Connections Bad or Damaged CableSFP Module Interface Settings10/100 and 10/100/1000 Port Connections 10/100 PoE or PoE+ Port ConnectionsAutonegotiation and Network Interface Cards Switch PerformanceSpanning Tree Loops Speed, Duplex, and AutonegotiationFinding the Switch Serial Number Resetting the SwitchSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Environmental Ranges Technical SpecificationsEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Available PoE SwitchOL-23803-02 10/100 and 10/100/1000 Ports Connector SpecificationsFigure B-2 10/100/1000 Port Pinouts SFP Module ConnectorsCables and Adapters SFP Module CablesCore Modal Wavelength TP3 Cable PinoutsSwitch Console RJ-45-to-DB-9 Port DTE Console Port Adapter PinoutsDevice Switch Console RJ-45-to-DB-25 Port DTE Adapter Device TxD RxDRxD TxD RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB Mini-Type B Console Port Figure C-2 Connecting the USB-Mini Console CableInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriversEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Switch or as a standalone switch Enter an enable secret password, and press ReturnEnter an enable password, and press Return Enter a virtual terminal Telnet password, and press ReturnThese choices appear OL-23803-02