Cisco Systems 3560-C manual Statement

Page 28

Chapter 2 Switch Installation

Preparing for Installation

Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001

Warning Read the installation instructions before connecting the system to the power source. Statement 1004

Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

20 A Statement 1005

Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack. Statement 1006

Warning Class 1 laser product. Statement 1008

Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024

Warning Ultimate disposal of this product should be handled according to all national laws and regulations. Statement 1040

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

2-2	OL-23803-02

Image 28

Contents Americas Headquarters Text Part Number OL-23803-02Page N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Switch Model DescriptionFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View PoE Ports Switches with PoE Ports 10/100 and 10/100/1000 Fast Ethernet Downlink PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L USB Type a Port Dual-Purpose PortsSFP Modules GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D=Management Ports USB Mini-Type B PortSwitch Panel LEDs LEDsSystem LED Console LEDsColor System Status Color DescriptionPort Mode Description Port status Port status. This is the default modeModes for Port LEDs Port LEDsDual-Purpose Port LEDs PoE LEDColor Meaning Security slot Power adapter connector Reset button Rear PanelAuxiliary Power Adapter Internal Power SupplyAuxiliary power adapter Management Options Reset ButtonSecurity Slots Network Configurations Cisco IOS CLISwitch Installation Preparing for InstallationStatement Installation Guidelines Box Contents Powering the SwitchEquipment That You Supply Verifying Switch Operation Mounting the SwitchDesk, Shelf, or Wall with Mounting Screws On a Desk or Shelf without Mounting ScrewsDesk- or Shelf-Mounting Installing the Mounting Screws on Top of a Desk or a Shelf Mounting the Switch on Top of a Desk or Shelf Under the Desk- or Shelf-MountingInstalling the Mounting Screws Under a Desk or Shelf Desk or shelf Screws Screw template AdhesiveWall-Mounting Desk or shelf Slides on this way77 in .49 cm 72 in .44 cm 46. 62 in .19 cm Switch Location of the Mounting Holes on the SwitchInstalling the Mounting Screws on the Wall With a Mounting Tray Mounting Tray with ScrewsSwitch Mounting tray Sliding direction Desk Installing the Switch on the Mounting TraySwitch Number-10 Phillips pan-head screws Mounting Tray with a MagnetPlace the switch on the mounting tray. See Figure 11 Placing the Switch on the Mounting Tray13 Wall-Mounting with a Magnet A Rack Attaching Brackets to the SwitchPhillips flat-head screw Mounting the Switch in a Rack 15 Attaching the 23-inch Brackets for Rack-MountingAttaching the DIN-Mount Tray to the Switch Place the switch on the DIN rail mount. See FigureSwitch DIN rail mount On a DIN RailMounting the Switch on a DIN Rail 18 Securing the DIN-Mount Tray to the Switch19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Installing a Cover for the Reset Button Optional Switch Reset button coverInstalling the Power Cord Retainer Optional 23 Inserting the Retainer through the Lanced LoopAC power cord Latches Sleeve for thin power cords Slide the retainer through the first latch. See Figure26 Sleeve Around the Power Cord Installing the Cable Guard Optional Washer29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Installing SFP Modules After Installing the SwitchNumber-8 Phillips wood screws Desk or shelf Removing SFP Modules TX and which is receive RXInsert a dust plug into the optical ports of the SFP module Grasp the SFP module, and carefully remove it from the slotConnecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsBale clasp Connecting to the PoE Ports Device Crossover CableWhere to Go Next OL-23803-02 Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE or PoE+ Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch Finding the Switch Serial NumberSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Technical Specifications Environmental RangesEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Switch Available PoEOL-23803-02 Connector Specifications 10/100 and 10/100/1000 PortsSFP Module Connectors Figure B-2 10/100/1000 Port PinoutsSFP Module Cables Cables and AdaptersCore Modal Wavelength Cable Pinouts TP3Console Port Adapter Pinouts Switch Console RJ-45-to-DB-9 Port DTEDevice TxD RxD Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceRxD TxD Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB-Mini Console Cable USB Mini-Type B Console PortInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Using the Add or Remove Programs UtilityIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter an enable secret password, and press Return Enter an enable password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switchThese choices appear OL-23803-02