Cisco Systems 3560-C manual Removing SFP Modules, TX and which is receive RX

Page 58

Chapter 2 Switch Installation

Removing SFP Modules

Warning Class 1 laser product. Statement 1008

Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

Step 2 Find the send (TX) and receive (RX) markings on the module top.

On some SFP modules, the TX and RX markings might be replaced by arrows that show the direction of the connection, either send or receive.

Step 3 If the module has a bale-clasp latch, move it to the open, unlocked position.

Step 4 Align the module in front of the slot opening, and push until you feel the connector snap into place. Step 5 If the module has a bale-clasp latch, close it.

Step 6 For fiber-optic SFP modules, remove the dust plugs and save.

Step 7 Connect the SFP cables.

Figure 2-34 Installing an SFP Module

5

 

Catal

 

 

 

 

yst3560-

 

 

 

6

C G

Series

 

PoE

 

 

 

 

 

 

 

 

 

8

 

 

 

 

9

 

 

 

10

 

 

208913

Caution Do not remove the dust plugs from the fiber-optic SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light.

Removing SFP Modules

 

 

 

Step 1

Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.

 

 

 

Step 2

Disconnect the cable from the SFP module. For reattachment, note which cable connector plug is send

 

 

 

 

(TX) and which is receive (RX).

 

 

 

Step 3

Insert a dust plug into the optical ports of the SFP module.

 

 

 

Step 4

If the module has a bale-clasp latch, pull the bale out and down to eject it. If the latch is obstructed and

 

 

 

 

you cannot use your finger, use a small, flat-blade screwdriver or other long, narrow instrument.

 

 

 

Step 5

Grasp the SFP module, and carefully remove it from the slot.

 

 

 

Step 6

Place the module in an antistatic bag or other protective environment.

 

 

 

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

 

 

 

 

 

 

 

 

 

 

2-32

 

 

OL-23803-02

 

 

 

 

 

Image 58
Contents Americas Headquarters Text Part Number OL-23803-02Page N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Switch Model DescriptionFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View PoE Ports Switches with PoE Ports 10/100 and 10/100/1000 Fast Ethernet Downlink PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L SFP Modules USB Type a PortDual-Purpose Ports GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D=Management Ports USB Mini-Type B PortSwitch Panel LEDs LEDsColor System Status System LEDConsole LEDs Color DescriptionModes for Port LEDs Port Mode DescriptionPort status Port status. This is the default mode Port LEDsDual-Purpose Port LEDs PoE LEDColor Meaning Security slot Power adapter connector Reset button Rear PanelAuxiliary Power Adapter Internal Power SupplyAuxiliary power adapter Management Options Reset ButtonSecurity Slots Network Configurations Cisco IOS CLISwitch Installation Preparing for InstallationStatement Installation Guidelines Box Contents Powering the SwitchEquipment That You Supply Verifying Switch Operation Mounting the SwitchDesk, Shelf, or Wall with Mounting Screws On a Desk or Shelf without Mounting ScrewsDesk- or Shelf-Mounting Installing the Mounting Screws on Top of a Desk or a Shelf Mounting the Switch on Top of a Desk or Shelf Under the Desk- or Shelf-MountingInstalling the Mounting Screws Under a Desk or Shelf Desk or shelf Screws Screw template AdhesiveWall-Mounting Desk or shelf Slides on this way77 in .49 cm 72 in .44 cm 46. 62 in .19 cm Switch Location of the Mounting Holes on the SwitchInstalling the Mounting Screws on the Wall With a Mounting Tray Mounting Tray with ScrewsSwitch Mounting tray Sliding direction Desk Installing the Switch on the Mounting TraySwitch Number-10 Phillips pan-head screws Mounting Tray with a MagnetPlace the switch on the mounting tray. See Figure 11 Placing the Switch on the Mounting Tray13 Wall-Mounting with a Magnet A Rack Attaching Brackets to the SwitchPhillips flat-head screw Mounting the Switch in a Rack 15 Attaching the 23-inch Brackets for Rack-MountingSwitch DIN rail mount Attaching the DIN-Mount Tray to the SwitchPlace the switch on the DIN rail mount. See Figure On a DIN RailMounting the Switch on a DIN Rail 18 Securing the DIN-Mount Tray to the Switch19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Installing a Cover for the Reset Button Optional Switch Reset button coverInstalling the Power Cord Retainer Optional 23 Inserting the Retainer through the Lanced LoopAC power cord Latches Sleeve for thin power cords Slide the retainer through the first latch. See Figure26 Sleeve Around the Power Cord Installing the Cable Guard Optional Washer29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Installing SFP Modules After Installing the SwitchNumber-8 Phillips wood screws Desk or shelf Insert a dust plug into the optical ports of the SFP module Removing SFP ModulesTX and which is receive RX Grasp the SFP module, and carefully remove it from the slotConnecting to the 10/100 and 10/100/1000 Ports Connecting Devices to the Ethernet PortsBale clasp Connecting to the PoE Ports Device Crossover CableWhere to Go Next OL-23803-02 Diagnosing Problems Switch Post ResultsBad or Damaged Cable Switch LEDsSwitch Connections Ethernet and Fiber-Optic Cables10/100 PoE or PoE+ Port Connections Interface Settings10/100 and 10/100/1000 Port Connections SFP ModuleSpeed, Duplex, and Autonegotiation Switch PerformanceSpanning Tree Loops Autonegotiation and Network Interface CardsResetting the Switch Finding the Switch Serial NumberSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Technical Specifications Environmental RangesEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Switch Available PoEOL-23803-02 Connector Specifications 10/100 and 10/100/1000 PortsSFP Module Connectors Figure B-2 10/100/1000 Port PinoutsSFP Module Cables Cables and AdaptersCore Modal Wavelength Cable Pinouts TP3Console Port Adapter Pinouts Switch Console RJ-45-to-DB-9 Port DTEDevice TxD RxD Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceRxD TxD Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB-Mini Console Cable USB Mini-Type B Console PortInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Using the Add or Remove Programs UtilityIP Settings Entering the Initial Configuration InformationCompleting the Setup Program Enter a virtual terminal Telnet password, and press Return Enter an enable secret password, and press ReturnEnter an enable password, and press Return Switch or as a standalone switchThese choices appear OL-23803-02