Cisco Systems 3560-C manual Wall-Mounting, Desk or shelf Slides on this way

Page 36

Mounting the Switch

Figure 2-4 Mounting the Switch Under a Desk or Shelf

1

2

2

1

E

8

NREHTE

EVO

REW PO

ELOSN OC

7

DP

6

D

P

esir Se

5

EoP

C-0296t s

4

3

ED

OM

alytaC

2

DPS

1

XL PD

TATS

T SYS

3

1

Desk or shelf

3

Slides on this way

2Screws

Chapter 2 Switch Installation

282395

After you mount the switch, see the “After Installing the Switch” section on page 2-31for information about configuring the switch.

Wall-Mounting

Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378

Caution Do not wall-mount the switch with its front panel facing up. Following safety regulations, wall-mount the switch with its front panel facing down or to the side to prevent airflow restriction and to provide easier access to the cables.

	Catalyst 3560-C and 2960-C Switch Hardware Installation Guide
2-10	OL-23803-02

Image 36

Contents Americas Headquarters Text Part Number OL-23803-02Page N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Obtaining Documentation and Submitting a Service Request Related PublicationsSwitch Models Switch Model DescriptionFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View PoE Ports Switches with PoE Ports 10/100 and 10/100/1000 Fast Ethernet Downlink PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L USB Type a Port Dual-Purpose PortsSFP Modules GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D=Management Ports USB Mini-Type B PortSwitch Panel LEDs LEDsSystem LED Console LEDsColor System Status Color DescriptionPort Mode Description Port status Port status. This is the default modeModes for Port LEDs Port LEDsPoE LED Dual-Purpose Port LEDsColor Meaning Security slot Power adapter connector Reset button Rear PanelInternal Power Supply Auxiliary Power AdapterAuxiliary power adapter Reset Button Management OptionsSecurity Slots Network Configurations Cisco IOS CLISwitch Installation Preparing for InstallationStatement Installation Guidelines Powering the Switch Box ContentsEquipment That You Supply Verifying Switch Operation Mounting the SwitchOn a Desk or Shelf without Mounting Screws Desk, Shelf, or Wall with Mounting ScrewsDesk- or Shelf-Mounting Installing the Mounting Screws on Top of a Desk or a Shelf Mounting the Switch on Top of a Desk or Shelf Under the Desk- or Shelf-MountingInstalling the Mounting Screws Under a Desk or Shelf Desk or shelf Screws Screw template AdhesiveWall-Mounting Desk or shelf Slides on this way77 in .49 cm 72 in .44 cm 46. 62 in .19 cm Switch Location of the Mounting Holes on the SwitchInstalling the Mounting Screws on the Wall With a Mounting Tray Mounting Tray with ScrewsSwitch Mounting tray Sliding direction Desk Installing the Switch on the Mounting TraySwitch Number-10 Phillips pan-head screws Mounting Tray with a MagnetPlace the switch on the mounting tray. See Figure 11 Placing the Switch on the Mounting Tray13 Wall-Mounting with a Magnet Attaching Brackets to the Switch A RackPhillips flat-head screw Mounting the Switch in a Rack 15 Attaching the 23-inch Brackets for Rack-MountingAttaching the DIN-Mount Tray to the Switch Place the switch on the DIN rail mount. See FigureSwitch DIN rail mount On a DIN RailMounting the Switch on a DIN Rail 18 Securing the DIN-Mount Tray to the Switch19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Installing a Cover for the Reset Button Optional Switch Reset button coverInstalling the Power Cord Retainer Optional 23 Inserting the Retainer through the Lanced LoopAC power cord Latches Sleeve for thin power cords Slide the retainer through the first latch. See Figure26 Sleeve Around the Power Cord Installing the Cable Guard Optional Washer29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch After Installing the Switch Installing SFP ModulesNumber-8 Phillips wood screws Desk or shelf Removing SFP Modules TX and which is receive RXInsert a dust plug into the optical ports of the SFP module Grasp the SFP module, and carefully remove it from the slotConnecting Devices to the Ethernet Ports Connecting to the 10/100 and 10/100/1000 PortsBale clasp Connecting to the PoE Ports Device Crossover CableWhere to Go Next OL-23803-02 Diagnosing Problems Switch Post ResultsSwitch LEDs Switch ConnectionsBad or Damaged Cable Ethernet and Fiber-Optic CablesInterface Settings 10/100 and 10/100/1000 Port Connections10/100 PoE or PoE+ Port Connections SFP ModuleSwitch Performance Spanning Tree LoopsSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsResetting the Switch Finding the Switch Serial NumberSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Technical Specifications Environmental RangesEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Switch Available PoEOL-23803-02 Connector Specifications 10/100 and 10/100/1000 PortsSFP Module Connectors Figure B-2 10/100/1000 Port PinoutsCables and Adapters SFP Module CablesCore Modal Wavelength Cable Pinouts TP3Switch Console RJ-45-to-DB-9 Port DTE Console Port Adapter PinoutsDevice Switch Console RJ-45-to-DB-25 Port DTE Adapter Device TxD RxDRxD TxD Accessing the CLI Through the Console Port RJ-45 Console PortFigure C-1 Connecting the Console Cable Figure C-2 Connecting the USB-Mini Console Cable USB Mini-Type B Console PortInstalling the Cisco Microsoft Windows USB Device Drivers Installing the Cisco Microsoft Windows XP USB DriverInstalling the Cisco Microsoft Windows 2000 USB Driver Uninstalling the Cisco Microsoft Windows USB Drivers Using the Add or Remove Programs UtilityEntering the Initial Configuration Information IP SettingsCompleting the Setup Program Enter an enable secret password, and press Return Enter an enable password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switchThese choices appear OL-23803-02