Cisco Systems 3560-C manual USB Type a Port, Dual-Purpose Ports, SFP Modules

Page 17

Chapter 1 Product Overview

Front Panel

PoE-Capable Downlink Ports (Catalyst 2960CPD-8PT-L, 3560CG-8PC-S, 3560CPD-8PT-S, 2960C-8PC-L, 2960C-12PC-L, 3560C-8PC-S, and 3560C-12PC-S)

Depending upon the available PoE budget, these switches can power other PoE-capable devices such as IP phones, access points, and so on. See Table 1-2for PoE budgeting information. See Figure 1-6.

For information on powering the switches, see the “Powering the Switch” section on page 2-4.

USB Type A Port

Some models have an USB Type A port. This port provides access to external Cisco USB flash devices (also known as thumb drives or USB keys). The port supports Cisco USB flash drives with capacities from 64 MB to 1 GB.

Cisco IOS software provides standard file system access to the flash device: read, write, erase, and copy, as well as the capability to format the flash device with a FAT file system.

For more information about the switch management ports, see the switch software configuration guide and the command reference on Cisco.com.

Dual-Purpose Ports

You can configure the dual-purpose ports on the switch as either 10/100/1000 ports or as SFP-module ports. You can set the 10/100/1000 ports to autonegotiate, or you can configure them as fixed 10, 100, or 1000 Mb/s (Gigabit) Ethernet ports.

By default, the switch selects the medium for each dual-purpose port (10/100/1000BASE-T or SFP). When a link is achieved on one media type, the switch disables the other media type until the active link goes down. If links are active on both media, the SFP-module port has priority, but you can use the media-typeinterface configuration command to manually designate the port as an RJ-45 port or an SFP port.

You can configure the speed and duplex settings consistent with the selected media type. For information on configuring interfaces, see the switch software configuration guide.

SFP Modules

The switch Ethernet SFP modules provide connections to other devices. These field-replaceable transceiver modules provide the uplink interfaces.The modules have LC connectors for fiber-optic connections or RJ-45 connectors for copper connections.

You can use any combination of these supported SFP modules:

•GLC-LH-SM=

•GLC-SX-MM=

•GLC-ZX-SM=

•GLC-BX-D=

•GLC-BX-U=

•GLC-FE-100FX=

•GLC-FE-100LX=

•GLC-FE-100BX-D=

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

 

OL-23803-02

1-9

 

 

 

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Text Part Number OL-23803-02 Americas HeadquartersPage N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Related Publications Obtaining Documentation and Submitting a Service RequestSwitch Model Description Switch ModelsFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View 10/100 and 10/100/1000 Fast Ethernet Downlink Ports PoE Ports Switches with PoE PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L Dual-Purpose Ports USB Type a PortSFP Modules GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D=USB Mini-Type B Port Management PortsLEDs Switch Panel LEDsConsole LEDs System LEDColor System Status Color DescriptionPort status Port status. This is the default mode Port Mode DescriptionModes for Port LEDs Port LEDsColor Meaning PoE LEDDual-Purpose Port LEDs Rear Panel Security slot Power adapter connector Reset buttonAuxiliary power adapter Internal Power SupplyAuxiliary Power Adapter Security Slots Reset ButtonManagement Options Cisco IOS CLI Network ConfigurationsPreparing for Installation Switch InstallationStatement Installation Guidelines Equipment That You Supply Powering the SwitchBox Contents Mounting the Switch Verifying Switch OperationDesk- or Shelf-Mounting On a Desk or Shelf without Mounting ScrewsDesk, Shelf, or Wall with Mounting Screws Installing the Mounting Screws on Top of a Desk or a Shelf Under the Desk- or Shelf-Mounting Mounting the Switch on Top of a Desk or ShelfDesk or shelf Screws Screw template Adhesive Installing the Mounting Screws Under a Desk or ShelfDesk or shelf Slides on this way Wall-MountingLocation of the Mounting Holes on the Switch 77 in .49 cm 72 in .44 cm 46. 62 in .19 cm SwitchInstalling the Mounting Screws on the Wall Mounting Tray with Screws With a Mounting TrayInstalling the Switch on the Mounting Tray Switch Mounting tray Sliding direction DeskMounting Tray with a Magnet Switch Number-10 Phillips pan-head screws11 Placing the Switch on the Mounting Tray Place the switch on the mounting tray. See Figure13 Wall-Mounting with a Magnet Phillips flat-head screw Attaching Brackets to the SwitchA Rack 15 Attaching the 23-inch Brackets for Rack-Mounting Mounting the Switch in a RackPlace the switch on the DIN rail mount. See Figure Attaching the DIN-Mount Tray to the SwitchSwitch DIN rail mount On a DIN Rail18 Securing the DIN-Mount Tray to the Switch Mounting the Switch on a DIN Rail19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Switch Reset button cover Installing a Cover for the Reset Button Optional23 Inserting the Retainer through the Lanced Loop Installing the Power Cord Retainer OptionalSlide the retainer through the first latch. See Figure AC power cord Latches Sleeve for thin power cords26 Sleeve Around the Power Cord Washer Installing the Cable Guard Optional29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Number-8 Phillips wood screws Desk or shelf After Installing the SwitchInstalling SFP Modules TX and which is receive RX Removing SFP ModulesInsert a dust plug into the optical ports of the SFP module Grasp the SFP module, and carefully remove it from the slotBale clasp Connecting Devices to the Ethernet PortsConnecting to the 10/100 and 10/100/1000 Ports Device Crossover Cable Connecting to the PoE PortsWhere to Go Next OL-23803-02 Switch Post Results Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables10/100 and 10/100/1000 Port Connections Interface Settings10/100 PoE or PoE+ Port Connections SFP ModuleSpanning Tree Loops Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsFinding the Switch Serial Number Resetting the SwitchSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Environmental Ranges Technical SpecificationsEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Available PoE SwitchOL-23803-02 10/100 and 10/100/1000 Ports Connector SpecificationsFigure B-2 10/100/1000 Port Pinouts SFP Module ConnectorsCore Modal Wavelength Cables and AdaptersSFP Module Cables TP3 Cable PinoutsDevice Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts RxD TxD Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceTxD RxD RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB Mini-Type B Console Port Figure C-2 Connecting the USB-Mini Console CableInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriversCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return Enter an enable secret password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switchThese choices appear OL-23803-02
Top Page Image Contents