Cisco Systems 3560-C manual Installation Guidelines

Page 29

Chapter 2 Switch Installation

Preparing for Installation

Warning For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: 10/100/1000 Ethernet. Statement 1044

Warning To prevent the system from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of: 113°F (45°C)

Statement 1047

Note For Catalyst 3560CG-8PC-S, 3560CG-8TC-S, and 2960CG-8TC-L switches, the maximum recommended ambient temperature is: 104°F (40°C).

Warning No user-serviceable parts inside. Do not open. Statement 1073

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning To prevent airflow restriction, allow clearance around the ventilation openings to be at least: 3 in. (7.6 cm) Statement 1076

Warning Hot surface. Statement 1079

Note Applies to the Catalyst 3560CG-8PC-S switch.

Installation Guidelines

Before installing the switch, these guidelines must be met:

•The operating environment must be within the ranges listed in Appendix A, “Technical Specifications.”

•Cabling is away from sources of electrical noise, such as radios, power lines, and fluorescent lighting fixtures. Make sure that the cabling is away from other devices that might damage the cables.

•Airflow around the switch and through the vents must be unrestricted. We strongly recommend that you allow at least 3 in. (7.6 cm) of clearance from the left, right, and top sides of the switch to avoid any flow blockage. If you are installing the switch in a rack, allow at least 1.75 in.

(4 cm) of empty rack space above each switch.

•Catalyst 3560CG-8PC-S, 2960C-8PC-L, 2960C-12PC-L, 3560C-8PC-S, and 3560C-12PC-S switches: Allow at least 1.75 in. (4 cm) clearance from the ends of the external heat sink fins.

Catalyst 3560-C and 2960-C Switch Hardware Installation Guide

	OL-23803-02	2-3

Image 29

Contents Text Part Number OL-23803-02 Americas HeadquartersPage N T E N T S Switch Installation Switch LEDs OL-23803-02 Preface Related Publications Obtaining Documentation and Submitting a Service RequestSwitch Model Description Switch ModelsFront Panel 3 4 Catalyst 3560CPD-8PT-S Front Panel View 10/100 and 10/100/1000 Fast Ethernet Downlink Ports PoE Ports Switches with PoE PortsPoE Pass-Through PoE Pass-Through PoE Budgeting for the Catalyst 2960CPD-8PT-L Dual-Purpose Ports USB Type a PortSFP Modules GLC-FE-100FX= GLC-FE-100LX= GLC-FE-100BX-D=USB Mini-Type B Port Management PortsLEDs Switch Panel LEDsConsole LEDs System LEDColor System Status Color DescriptionPort status Port status. This is the default mode Port Mode DescriptionModes for Port LEDs Port LEDsColor Meaning PoE LEDDual-Purpose Port LEDs Rear Panel Security slot Power adapter connector Reset buttonAuxiliary power adapter Internal Power SupplyAuxiliary Power Adapter Security Slots Reset ButtonManagement Options Cisco IOS CLI Network ConfigurationsPreparing for Installation Switch InstallationStatement Installation Guidelines Equipment That You Supply Powering the SwitchBox Contents Mounting the Switch Verifying Switch OperationDesk- or Shelf-Mounting On a Desk or Shelf without Mounting ScrewsDesk, Shelf, or Wall with Mounting Screws Installing the Mounting Screws on Top of a Desk or a Shelf Under the Desk- or Shelf-Mounting Mounting the Switch on Top of a Desk or ShelfDesk or shelf Screws Screw template Adhesive Installing the Mounting Screws Under a Desk or ShelfDesk or shelf Slides on this way Wall-MountingLocation of the Mounting Holes on the Switch 77 in .49 cm 72 in .44 cm 46. 62 in .19 cm SwitchInstalling the Mounting Screws on the Wall Mounting Tray with Screws With a Mounting TrayInstalling the Switch on the Mounting Tray Switch Mounting tray Sliding direction DeskMounting Tray with a Magnet Switch Number-10 Phillips pan-head screws11 Placing the Switch on the Mounting Tray Place the switch on the mounting tray. See Figure13 Wall-Mounting with a Magnet Phillips flat-head screw Attaching Brackets to the SwitchA Rack 15 Attaching the 23-inch Brackets for Rack-Mounting Mounting the Switch in a RackPlace the switch on the DIN rail mount. See Figure Attaching the DIN-Mount Tray to the SwitchSwitch DIN rail mount On a DIN Rail18 Securing the DIN-Mount Tray to the Switch Mounting the Switch on a DIN Rail19 Mounting the Switch on a DIN Rail Removing the Switch from a DIN Rail Switch Reset button cover Installing a Cover for the Reset Button Optional23 Inserting the Retainer through the Lanced Loop Installing the Power Cord Retainer OptionalSlide the retainer through the first latch. See Figure AC power cord Latches Sleeve for thin power cords26 Sleeve Around the Power Cord Washer Installing the Cable Guard Optional29 Attaching the Cable Guard to the Switch 31 Attaching the Cables to the Switch Number-8 Phillips wood screws Desk or shelf After Installing the SwitchInstalling SFP Modules TX and which is receive RX Removing SFP ModulesInsert a dust plug into the optical ports of the SFP module Grasp the SFP module, and carefully remove it from the slotBale clasp Connecting Devices to the Ethernet PortsConnecting to the 10/100 and 10/100/1000 Ports Device Crossover Cable Connecting to the PoE PortsWhere to Go Next OL-23803-02 Switch Post Results Diagnosing ProblemsSwitch Connections Switch LEDsBad or Damaged Cable Ethernet and Fiber-Optic Cables10/100 and 10/100/1000 Port Connections Interface Settings10/100 PoE or PoE+ Port Connections SFP ModuleSpanning Tree Loops Switch PerformanceSpeed, Duplex, and Autonegotiation Autonegotiation and Network Interface CardsFinding the Switch Serial Number Resetting the SwitchSerial Number Location for the Catalyst 3560CPD-8PT-S Switch 330039 OL-23803-02 Environmental Ranges Technical SpecificationsEnvironmental Ranges Physical Specifications Power Requirements Table A-2 Catalyst 3560-C and 2960-C Switch Specifications Available PoE SwitchOL-23803-02 10/100 and 10/100/1000 Ports Connector SpecificationsFigure B-2 10/100/1000 Port Pinouts SFP Module ConnectorsCore Modal Wavelength Cables and AdaptersSFP Module Cables TP3 Cable PinoutsDevice Switch Console RJ-45-to-DB-9 Port DTEConsole Port Adapter Pinouts RxD TxD Switch Console RJ-45-to-DB-25 Port DTE Adapter DeviceTxD RxD RJ-45 Console Port Accessing the CLI Through the Console PortFigure C-1 Connecting the Console Cable USB Mini-Type B Console Port Figure C-2 Connecting the USB-Mini Console CableInstalling the Cisco Microsoft Windows XP USB Driver Installing the Cisco Microsoft Windows USB Device DriversInstalling the Cisco Microsoft Windows 2000 USB Driver Using the Add or Remove Programs Utility Uninstalling the Cisco Microsoft Windows USB DriversCompleting the Setup Program Entering the Initial Configuration InformationIP Settings Enter an enable password, and press Return Enter an enable secret password, and press ReturnEnter a virtual terminal Telnet password, and press Return Switch or as a standalone switchThese choices appear OL-23803-02