Cisco Systems 10BASE-FL, PA-5EFL= manual VIP2 and the 5EFL Port Adapter

Page 11

5EFL Port Adapter Multimode Fiber-Optic Cable and Receptacles

5EFL Port Adapter Multimode Fiber-Optic Cable and Receptacles

The interface connectors on the 5EFL port adapter are ﬁve pairs of (ST) receptacles, designated as RX and TX. You can use all ﬁve connection pairs simultaneously or any combination of each pair individually. Each connection pair supports IEEE 802.3 and Ethernet 10BASE-FL interfaces compliant with appropriate standards. Figure 6 shows the ST ﬁber-optic cable plug used for RX and TX connections.

Figure 6 Ethernet 10BASE-FL Fiber-Optic Cable Plug (ST Type)

H1348a

Note The 5EFL interfaces on a VIP2 are conﬁgured for 10 Mbps, half duplex, for a maximum aggregate bandwidth of 50 Mbps for half-duplex. Cisco Systems does not supply ST-type optical-ﬁber cables; these cables are available commercially. For ST-type, multimode optical-ﬁber cable speciﬁcations and transmission distance limitations and requirements, refer to the section “IEEE 802.3 10BASE-FL Speciﬁcations” on page 7.

VIP2 and the 5EFL Port Adapter

This section describes the 5EFL port adapter and its use with the VIP2.

The following sections provide additional information speciﬁc to the 5EFL port adapter and its use on the VIP2 in Cisco 7000 series and Cisco 7500 series routers:

•

•

•

Installing or Replacing a Port Adapter on a VIP2, page 13

Attaching 5EFL Port Adapter Interface Cables, page 17

Conﬁguring the 5EFL Interfaces, page 17

—Selecting Chassis Slot, Port Adapter, and Ethernet 10BASE-FL Interface Port Numbers, page 18

—Conﬁguring the 5EFL Interfaces, page 17

—Checking the Conﬁguration, page 20

The 5EFL port adapter can be installed on the VIP2 in port adapter slot 0 and port adapter slot 1. Figure 7 shows two 5EFL port adapters installed in port adapter slots 0 and 1 on a VIP2-15 or VIP2-40.

PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 11

Image 11

Contents Introduction ContentsIf You Need More Information Port Adapter Installation PrerequisitesIf You Need More Information PA-5EFL Port Adapter Software Requirements Tools and Parts RequiredSoftware and Hardware Requirements Tools and Parts RequiredSafety Guidelines Safety GuidelinesSafety Warnings Electrical Equipment Guidelines Safety WarningsPreventing Electrostatic Discharge Damage Telephone Wiring GuidelinesEthernet and Ethernet 10BASE-FL Overview Parameter Ethernet Ieee 802.3 10BASE-FL SpecificationsIeee 802.3 10BASE-FL Speciﬁcations IeeeParameter Multimode What Is the 5EFL Port Adapter?What Is the 5EFL Port Adapter? Multimode Optical-Fiber ParametersTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown Port Adapters in the Cisco 5EFL Port Adapter LEDsEthernet 10BASE-FL Fiber-Optic Cable Plug ST Type VIP2 and the 5EFL Port AdapterSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Attaching 5EFL Port Adapter Interface CablesConﬁguring the 5EFL Interfaces VIP2 and the 5EFL Port Adapter Conﬁguring Interfaces Configuring the 5EFL InterfacesStep Using show Commands to Verify the VIP2 StatusChecking the Conﬁguration Router# sh int e 3/0/0 Using show Commands to Display Interface InformationRouter# sh int e 3/1/0 Router# show version Router# show diag Using the ping CommandCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Guide Replacing a Port AdapterPort adapter Handle Attaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Router# sh int e 2/0 Cisco 7200 Series and the 5EFL Port Adapter StepLast reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM Documentation CD-ROM Documentation CD-ROM