Cisco Systems PA-5EFL= manual What Is the 5EFL Port Adapter?, Multimode Optical-Fiber Parameters

Page 8

What Is the 5EFL Port Adapter?

Table 4 lists multimode optical-fiber parameters.

Table 4

Multimode Optical-Fiber Parameters

 

 

Parameter

Multimode

 

 

Size

62.5/125 micrometer (nominal diameter) optical fiber 1

Attenuation

3.75 dB/km, at 850 nanometers (nm)

 

 

Insertion loss

< 12.5 dB, at 850 nm

 

 

Bandwidth

> 160MHzkm, at 850 nm

 

 

Propagation delay

5 microseconds/km

 

 

1 Specified in IEC Publication 793-2[14].

What Is the 5EFL Port Adapter?

The 5EFL port adapter provides up to five IEEE 802.3 Ethernet 10BASE-FL interfaces. (See Figure 1.) Each Ethernet 10BASE-FL interface allows a maximum bandwidth of 10 Mbps, for a maximum aggregate bandwidth of 50 Mbps, half-duplex. Each 10BASE-FL interface uses two multimode (ST) receptacles for receive (RX) and transmit (TX). All five ports run at wire speed.

Figure 1

5EFL Port Adapter, Faceplate View

 

 

 

 

 

EN

 

 

 

 

 

 

 

ETHERNET-10BFL

 

 

 

 

 

 

 

 

 

 

RX

TX

RX

TX

RX

TX

RX

TX

RX

TX

0

 

 

1

2

 

 

3

4

 

H6471

Port Adapter Locations on the VIP2 and in the Cisco 7200 Series Routers

This section provides information about where you can install the 5EFL port adapter on the VIP2 and in the Cisco 7200 series routers.

Note Port adapters have handles that allow for easy installation and removal; however, they are occasionally not shown in this publication to highlight port adapter faceplate detail.

Figure 2 shows a VIP2-15 or VIP2-40 with two installed port adapters. Figure 3 shows a VIP2-50 with two installed port adapters. With the VIP2 oriented as shown, the left port adapter is in port adapter slot 0, and the right port adapter is in port adapter slot 1.

8PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration

Image 8
Contents Contents IntroductionIf You Need More Information Port Adapter Installation PrerequisitesIf You Need More Information Tools and Parts Required Software and Hardware RequirementsTools and Parts Required PA-5EFL Port Adapter Software RequirementsSafety Guidelines Safety GuidelinesSafety Warnings Safety Warnings Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage Telephone Wiring GuidelinesEthernet and Ethernet 10BASE-FL Overview Ieee 802.3 10BASE-FL Specifications Ieee 802.3 10BASE-FL SpecificationsIeee Parameter EthernetWhat Is the 5EFL Port Adapter? What Is the 5EFL Port Adapter?Multimode Optical-Fiber Parameters Parameter MultimodeTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown 5EFL Port Adapter LEDs Port Adapters in the CiscoVIP2 and the 5EFL Port Adapter Ethernet 10BASE-FL Fiber-Optic Cable Plug ST TypeSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Attaching 5EFL Port Adapter Interface CablesConfiguring the 5EFL Interfaces VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Configuring InterfacesStep Using show Commands to Verify the VIP2 StatusChecking the Configuration Using show Commands to Display Interface Information Router# sh int e 3/0/0Router# sh int e 3/1/0 Router# show version Using the ping Command Router# show diagCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Replacing a Port Adapter GuidePort adapter Handle Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Cisco 7200 Series and the 5EFL Port Adapter Step Router# sh int e 2/0Last reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM Documentation CD-ROM Documentation CD-ROM