Cisco Systems PA-5EFL=, 10BASE-FL manual VIP2 and the 5EFL Port Adapter

Page 18

VIP2 and the 5EFL Port Adapter

After you verify that the new 5EFL port adapter is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Be prepared with the information you will need, such as the following:

•

•

•

Protocols you plan to route on each new interface.

Internet protocol (IP) addresses if you plan to configure the interfaces for IP routing.

Whether the new interfaces will use bridging.

For a summary of the configuration options available and instructions for configuring the 5EFL interfaces on the VIP2, refer to the appropriate configuration publications listed in the section “If You Need More Information” on page 2.

The configure command requires privileged-level access to the EXEC command interpreter, which usually requires a password. Contact your system administrator if necessary to obtain EXEC-level access.

Selecting Chassis Slot, Port Adapter, and Ethernet 10BASE-FL Interface Port Numbers

The following section describes how to identify chassis slot, port adapter, and Ethernet 10BASE-FL interface port numbers.

Note Although the processor slots in the seven-slot Cisco 7000 and Cisco 7507 and 13-slot Cisco 7513 are vertically oriented and those in the five-slot Cisco 7010 and Cisco 7505 are horizontally oriented, all models use the same method for slot and port numbering.

In the router, physical port addresses specify the actual physical location of each interface port on the router interface processor end. (See Figure 14.) This address is composed of a three-part number in the format chassis slot number/port adapter number/interface port number, as follows:

•The first number identifies the chassis slot in which the VIP2 is installed (as shown in the example system in Figure 14).

•The second number identifies the physical port adapter number on the VIP2, and is either 0 or 1.

•The third number indicates the interface ports on each 5EFL port adapter are always numbered in sequence as interface 0 through 4.

Interface ports on the VIP2 maintain the same address regardless of whether other interface processors are installed or removed. However, when you move a VIP2 to a different slot, the first number in the address changes to reflect the new slot number.

Figure 14 shows some of the slot port adapter and interface ports of a sample Cisco 7505 system. For example, on a VIP2 equipped with a 5EFL port adapter in slot 3, the addresses of the first 5EFL port adapter are 3/0/0 through 3/0/4 (chassis slot 3, port adapter slot 0, and interface ports 0–4), and the addresses of the second 5EFL port adapter are 3/1/0 through 3/1/4 (chassis slot 3, port adapter slot 0, and interface ports 0–4)

The first port adapter slot number is always 0. The second port adapter slot number is always 1. The individual interface port numbers always begin with 0. For example, in Figure 14, the five 10BASE-FL interface ports on the 5EFL port adapter in the first port adapter slot in chassis slot 3, have the following addresses: 3/0/0, 3/0/1, 3/0/2, 3/0/3, and 3/0/4. (See Figure 14.) The interfaces on the second 5EFL port adapter have the following addresses: 3/1/0, 3/1/1, 3/1/2, 3/1/3, and 3/1/4.

18PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Contents IntroductionPort Adapter Installation Prerequisites If You Need More InformationIf You Need More Information Tools and Parts Required Tools and Parts RequiredSoftware and Hardware Requirements PA-5EFL Port Adapter Software RequirementsSafety Guidelines Safety WarningsSafety Guidelines Safety Warnings Electrical Equipment GuidelinesTelephone Wiring Guidelines Ethernet and Ethernet 10BASE-FL OverviewPreventing Electrostatic Discharge Damage Ieee Ieee 802.3 10BASE-FL SpecificationsIeee 802.3 10BASE-FL Specifications Parameter EthernetMultimode Optical-Fiber Parameters What Is the 5EFL Port Adapter?What Is the 5EFL Port Adapter? Parameter MultimodeTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown 5EFL Port Adapter LEDs Port Adapters in the CiscoVIP2 and the 5EFL Port Adapter Ethernet 10BASE-FL Fiber-Optic Cable Plug ST TypeSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL InterfacesAttaching 5EFL Port Adapter Interface Cables VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Configuring InterfacesUsing show Commands to Verify the VIP2 Status Checking the ConfigurationStep Using show Commands to Display Interface Information Router# sh int e 3/0/0Router# sh int e 3/1/0 Router# show version Using the ping Command Router# show diagCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Replacing a Port Adapter GuidePort adapter Handle Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Cisco 7200 Series and the 5EFL Port Adapter Step Router# sh int e 2/0Last reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Documentation CD-ROMCisco Connection Online Documentation CD-ROM Documentation CD-ROM
Top Page Image Contents