Cisco Systems 10BASE-FL, PA-5EFL= manual Last reset from power-on Bridging software

Page 35

Configuring the 5EFL Interfaces

The following example of the show interfaces ethernet slot/port command shows all of the information specific to the first 5EFL interface port (interface port 0) in port adapter slot 2:

Router# sh int e 2/0

Ethernet2/0 is administratively down, line protocol is down Hardware is AmdP2 Ethernet, address is 1.1.1.10 (bia 0000.0ca5.238e)

MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 1/255 Encapsulation ARPA, loopback not set, keepalive set (10 sec)

ARP type: ARPA, ARP Timeout 4:00:00

Last input never, output never, output hang never Last clearing of "show interface" counters 2:56:26 Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 input packets with dribble condition detected

0 packets output, 0 bytes, 0 underruns

0 output errors, 0 collisions, 0 interface resets, 0 restarts 0 output buffer failures, 0 output buffers swapped out

The show version (or show hardware) command displays the configuration of the system hardware (the number of each interface processor type installed), the software version, the names and sources of configuration files, and the boot images. Following is an example of the show version command:

Router# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-J-M), Version 11.1(472) [biff 105]

Copyright (c) 1986-1996 by cisco Systems, Inc.

Compiled Fri 06-Oct-96 12:22 by

Image text-base: 0x600088A0, data-base: 0x605A4000

ROM: System Bootstrap, Version 11.1(10979) RELEASED SOFTWARE

Router uptime is 8 hours, 22 minutes

System restarted by reload

System image file is "slot0:c7200-j-mz.960421", booted via slot0

cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0

Last reset from power-on Bridging software.

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface.

5 Ethernet/IEEE 802.3 interfaces.

1 Serial network interfaces.

125K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2

PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 35

Page 34 Page 36
Image 35
Page 34 Page 36
Contents Introduction ContentsIf You Need More Information Port Adapter Installation PrerequisitesIf You Need More Information PA-5EFL Port Adapter Software Requirements Tools and Parts RequiredSoftware and Hardware Requirements Tools and Parts RequiredSafety Guidelines Safety GuidelinesSafety Warnings Electrical Equipment Guidelines Safety WarningsPreventing Electrostatic Discharge Damage Telephone Wiring GuidelinesEthernet and Ethernet 10BASE-FL Overview Parameter Ethernet Ieee 802.3 10BASE-FL SpecificationsIeee 802.3 10BASE-FL Specifications IeeeParameter Multimode What Is the 5EFL Port Adapter?What Is the 5EFL Port Adapter? Multimode Optical-Fiber ParametersTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown Port Adapters in the Cisco 5EFL Port Adapter LEDsEthernet 10BASE-FL Fiber-Optic Cable Plug ST Type VIP2 and the 5EFL Port AdapterSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Attaching 5EFL Port Adapter Interface CablesConfiguring the 5EFL Interfaces VIP2 and the 5EFL Port Adapter Configuring Interfaces Configuring the 5EFL InterfacesStep Using show Commands to Verify the VIP2 StatusChecking the Configuration Router# sh int e 3/0/0 Using show Commands to Display Interface InformationRouter# sh int e 3/1/0 Router# show version Router# show diag Using the ping CommandCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Guide Replacing a Port AdapterPort adapter Handle Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Router# sh int e 2/0 Cisco 7200 Series and the 5EFL Port Adapter StepLast reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM Documentation CD-ROM Documentation CD-ROM
Top Page Image Contents