Cisco Systems PA-5EFL=, 10BASE-FL manual Safety Guidelines, Safety Warnings

Page 4

Safety Guidelines

Note Port adapters used with the 7200 VXR routers require the correct base hardware revision in order to function. The following error message will occur on bootup if the incorrect hardware revision is used:

>PA-3-REVNOTSUPPORTED:PA in slot 1 (Ethernet) requires base h/w revision of (1.5) for this chassis

Use the sh diag command to display the hardware revision. (See the “Using show Commands to

Display Interface Information” section on page 34).

Note The minimum recommended VIP2 model is a VIP2-15.

Safety Guidelines

Following are safety guidelines that you should follow when working with any equipment that connects to electrical power or telephone wiring.

Safety Warnings

Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement.

Warning Means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device.

Waarschuwing Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het document Regulatory Compliance and Safety Information (Informatie over naleving van veiligheids- en andere voorschriften) raadplegen dat bij dit toestel is ingesloten.

Varoitus Tämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. Tässä julkaisussa esiintyvien varoitusten käännökset löydät laitteen mukana olevasta Regulatory Compliance and Safety Information -kirjasesta (määräysten noudattaminen ja tietoa turvallisuudesta).

Attention Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant causer des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions d’avertissements figurant dans cette publication, consultez le document Regulatory Compliance and Safety Information (Conformité aux règlements et consignes de sécurité) qui accompagne cet appareil.

4PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Contents IntroductionIf You Need More Information Port Adapter Installation PrerequisitesIf You Need More Information Tools and Parts Required Software and Hardware RequirementsTools and Parts Required PA-5EFL Port Adapter Software RequirementsSafety Warnings Safety GuidelinesSafety Guidelines Safety Warnings Electrical Equipment GuidelinesEthernet and Ethernet 10BASE-FL Overview Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Ieee 802.3 10BASE-FL Specifications Ieee 802.3 10BASE-FL SpecificationsIeee Parameter EthernetWhat Is the 5EFL Port Adapter? What Is the 5EFL Port Adapter?Multimode Optical-Fiber Parameters Parameter MultimodeTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown 5EFL Port Adapter LEDs Port Adapters in the CiscoVIP2 and the 5EFL Port Adapter Ethernet 10BASE-FL Fiber-Optic Cable Plug ST TypeSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Attaching 5EFL Port Adapter Interface CablesAttaching 5EFL Port Adapter Interface Cables VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Configuring InterfacesChecking the Configuration Using show Commands to Verify the VIP2 StatusStep Using show Commands to Display Interface Information Router# sh int e 3/0/0Router# sh int e 3/1/0 Router# show version Using the ping Command Router# show diagCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Replacing a Port Adapter GuidePort adapter Handle Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Cisco 7200 Series and the 5EFL Port Adapter Step Router# sh int e 2/0Last reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Documentation CD-ROM Cisco Connection OnlineCisco Connection Online Documentation CD-ROM Documentation CD-ROM
Top Page Image Contents