Cisco 7200 Series and the 5EFL Port Adapter
Figure 21 shows the port adapter slots and interface ports of a Cisco 7206. The port adapter slot numbers start with 1 and continue through 6 (slot 0 is always reserved for the Fast Ethernet port on the I/O controller—if present). The individual interface port numbers always begin with 0. The number of additional ports depends on the number of ports on a port adapter.
For example, the five interface ports on a 5EFL port adapter in port adapter slot 1 would have the addresses 1/0 through 1/4. (See Figure 21.) If the 5EFL port adapter was in port adapter slot 5, these same interface ports would be numbered 5/0 through 5/4. Port adapters can occupy any port adapter slot. There are no restrictions.
Figure 21 10BASE-FL Interface Port Number Example
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| TOKEN RING |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 6 |
5 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ETHERNET 10BT |
|
|
|
|
|
|
|
|
|
|
|
| FAST ETHERNET |
|
| ||
|
|
|
|
|
|
|
| ENABLED |
|
|
|
|
|
| LINK | RJ45 |
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
| MII |
|
|
|
|
| 4 | ||||
3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FAST SERIAL |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| EN |
| RX |
|
| TX | RX | TX | RX | TX | RX | TX | RX |
| TX |
| 2 |
|
|
|
|
|
|
|
|
|
|
|
| 4 |
| |||||||||||
1 |
|
|
|
|
|
|
|
|
|
| 0 |
|
|
| 1 | 2 |
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| SLOT | 1 |
| MII |
|
|
|
|
|
|
|
|
| FAST ETHERNET INPUT/OUTPUT CONTROLLER |
|
|
| ||||
|
|
|
|
| FE |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| H6772 | |||
|
|
|
|
|
|
|
|
|
|
|
| RJ |
|
|
|
|
|
|
|
| 0 | |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
ENABLED |
| EJECT |
| 0 |
|
|
| MII |
| PWR |
|
|
|
|
|
|
|
|
| |||||
PCMCIA | SLOT |
|
|
|
| EN |
| EN |
| LINK | 1O | OK |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
5 EFL port adapter
(port numbers 2/0, 2/1, 2/2 and 2/3 from left ot right)
You can identify interface ports by physically checking the slot/interface port location on the front of the router or by using show commands to display information about a specific interface or all interfaces in the router.
Configuring Interfaces
The following steps describe a basic interface configuration. Press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:
Router# disable
Router>
Use the following procedure to perform a basic configuration:
Step 1 At the
terminal will be the source of the configuration subcommands, as follows:
Router# configure terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#
32