Cisco Systems 10BASE-FL, PA-5EFL= Two Port Adapters on a VIP2-50 Horizontal Orientation Shown

Page 9

Port Adapter Locations on the VIP2 and in the Cisco 7200 Series Routers

Figure 2 Two Port Adapters on a VIP2-15 or VIP2-40 (Horizontal Orientation Shown)

	Bus connector	CPU Boot ROM
		U6
		U2	DRAM
	SRAM	U2	SIMMs
	SRAM	U4	SIMMs
	DIMM U5
	Port adapter		Port adapter
	in slot 0		in slot 1
			H6448

Figure 3 Two Port Adapters on a VIP2-50 (Horizontal Orientation Shown)

Boot ROM	CPU
Bus connector
SRAM
daughter	DRAM DIMM
card	DRAM DIMM

Port adapter in slot 0

Port adapter in slot 1

H10447

Note In the Cisco 7000, Cisco 7507, and Cisco 7513 chassis, the VIP2 is installed vertically. In the Cisco 7010 and Cisco 7505 chassis, the VIP2 is installed horizontally.

Figure 4 shows a Cisco 7206 with port adapters installed. In the Cisco 7206 and Cisco 7206VXR, port adapter slot 1 is in the lower left position and port adapter slot 6 is in the upper right position. The Cisco 7204 and Cisco 7204VXR are not shown, but have four port adapter slots; PA-5EFL can be installed in any of these four slots.

PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 9

Image 9

Contents Introduction ContentsPort Adapter Installation Prerequisites If You Need More InformationIf You Need More Information Software and Hardware Requirements Tools and Parts RequiredTools and Parts Required PA-5EFL Port Adapter Software RequirementsSafety Guidelines Safety WarningsSafety Guidelines Electrical Equipment Guidelines Safety WarningsTelephone Wiring Guidelines Ethernet and Ethernet 10BASE-FL OverviewPreventing Electrostatic Discharge Damage Ieee 802.3 10BASE-FL Speciﬁcations Ieee 802.3 10BASE-FL SpecificationsIeee Parameter EthernetWhat Is the 5EFL Port Adapter? What Is the 5EFL Port Adapter?Multimode Optical-Fiber Parameters Parameter MultimodeTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown Port Adapters in the Cisco 5EFL Port Adapter LEDsEthernet 10BASE-FL Fiber-Optic Cable Plug ST Type VIP2 and the 5EFL Port AdapterSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL InterfacesAttaching 5EFL Port Adapter Interface Cables VIP2 and the 5EFL Port Adapter Conﬁguring Interfaces Configuring the 5EFL InterfacesUsing show Commands to Verify the VIP2 Status Checking the ConﬁgurationStep Router# sh int e 3/0/0 Using show Commands to Display Interface InformationRouter# sh int e 3/1/0 Router# show version Router# show diag Using the ping CommandCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Guide Replacing a Port AdapterPort adapter Handle Attaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Router# sh int e 2/0 Cisco 7200 Series and the 5EFL Port Adapter StepLast reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Documentation CD-ROMCisco Connection Online Documentation CD-ROM Documentation CD-ROM