Cisco Systems PA-5EFL=, 10BASE-FL manual Attaching 5EFL Port Adapter Interface Cables

Page 30

Cisco 7200 Series and the 5EFL Port Adapter

Attaching 5EFL Port Adapter Interface Cables

On a single 5EFL port adapter, you can use up to ﬁve pairs of ST ﬁber-optic connections. The 5EFL port adapter is an end station device and not a repeater; you must connect the 5EFL port adapter to a 10BASE-FL repeater or hub. ST-type ﬁber-optic cables are not available from Cisco Systems; they are available from outside commercial cable vendors.

Connect ST ﬁber-optic cables to the 5EFL port adapter as follows:

Step 1 Attach the RX multimode ﬁber-optic cable directly to the RX port on the 5EFL port adapter. (See Figure 20.)

Note Port adapters have a handle attached, but it is not shown in Figure 20 to allow a full view of the detail on each port adapter’s faceplate.

Step 2 Attach the TX multimode ﬁber-optic cable directly to the TX port on the 5EFL port adapter. (See Figure 20.)

Figure 20 Connecting 5EFL Port Adapter ST Cable Pairs

EN								ETHERNET-10BFL
EN
RX	TX	RX	TX	RX	TX	RX	TX	RX	TX
	0		1		2		3	4

RXTX

ST-type optical-fiber cables; two for each 5EFL port

H6770

To the appropriate TX and RX ports of the repeater, hub, DTE or other external 10BASE-FL equipment

Step 3 Connect a 5EFL RX port to the appropriate TX port of the repeater, hub, DTE, or other external 10BASE-FL equipment.

Step 4 Connect a 5EFL TX port to the appropriate RX port of the repeater, hub, DTE, or other external 10BASE-FL equipment.

Step 5 Repeat Steps 1 and 4 for each additional 5EFL interface connection you require.

This completes cable connection to the 5EFL port adapter.

30PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Conﬁguration

Image 30

Contents Contents IntroductionPort Adapter Installation Prerequisites If You Need More InformationIf You Need More Information Tools and Parts Required Tools and Parts RequiredSoftware and Hardware Requirements PA-5EFL Port Adapter Software RequirementsSafety Guidelines Safety WarningsSafety Guidelines Safety Warnings Electrical Equipment GuidelinesTelephone Wiring Guidelines Ethernet and Ethernet 10BASE-FL OverviewPreventing Electrostatic Discharge Damage Ieee Ieee 802.3 10BASE-FL SpecificationsIeee 802.3 10BASE-FL Speciﬁcations Parameter EthernetMultimode Optical-Fiber Parameters What Is the 5EFL Port Adapter?What Is the 5EFL Port Adapter? Parameter MultimodeTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown 5EFL Port Adapter LEDs Port Adapters in the CiscoVIP2 and the 5EFL Port Adapter Ethernet 10BASE-FL Fiber-Optic Cable Plug ST TypeSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Attaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL InterfacesAttaching 5EFL Port Adapter Interface Cables VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Conﬁguring InterfacesUsing show Commands to Verify the VIP2 Status Checking the ConﬁgurationStep Using show Commands to Display Interface Information Router# sh int e 3/0/0Router# sh int e 3/1/0 Router# show version Using the ping Command Router# show diagCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Replacing a Port Adapter GuidePort adapter Handle Attaching 5EFL Port Adapter Interface Cables Conﬁguring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Cisco 7200 Series and the 5EFL Port Adapter Step Router# sh int e 2/0Last reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Cisco Connection Online Documentation CD-ROMCisco Connection Online Documentation CD-ROM Documentation CD-ROM