Cisco Systems 10BASE-FL, PA-5EFL= manual Configuring the 5EFL Interfaces

Page 31

Configuring the 5EFL Interfaces

Configuring the 5EFL Interfaces

If you installed a new 5EFL port adapter or if you want to change the configuration of an existing interface, you must enter configuration mode using the configure command. If you replaced a 5EFL port adapter that was previously configured, the system will recognize the new 5EFL interfaces and bring them up in their existing configuration.

After you verify that the new 5EFL port adapter is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interfaces. Be prepared with the information you will need, such as the following:

•

•

•

Protocols you plan to route on each new interface.

Internet protocol (IP) addresses if you plan to configure the interfaces for IP routing.

Whether the new interfaces will use bridging.

For a summary of the configuration options available and instructions for configuring the 4E interfaces on a Cisco 7200 series router, refer to the appropriate configuration publications listed in the section “If You Need More Information” on page 2.

The configure command requires privileged-level access to the EXEC command interpreter, which usually requires a password. Contact your system administrator if necessary to obtain EXEC-level access.

Selecting Port Adapter Slot and Ethernet 10BASE-FL Interface Port Numbers

The following section describes how to identify port adapter slot and Ethernet 10BASE-FL interface port numbers.

Physical port addresses specify the actual physical location of each interface port on the router. (See Figure 21.) This address is composed of a two-part number in the format port adapter slot number/interface port number, as follows:

•The first number identifies the chassis slot in which the in which the 5EFL is installed.

•The second number identifies the interface ports on each 5EFL port adapter, which are always numbered in sequence as interface 0 through 4.

Interface ports maintain the same address regardless of whether other port adapters are installed or removed from the slot. However, when you move a port adapter to a different slot, the first number in the address changes to reflect the new chassis slot number.

PA-5EFL Ethernet 10BASE-FL Port Adapter Installation and Configuration 31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Introduction ContentsIf You Need More Information Port Adapter Installation PrerequisitesIf You Need More Information PA-5EFL Port Adapter Software Requirements Tools and Parts RequiredSoftware and Hardware Requirements Tools and Parts RequiredSafety Warnings Safety GuidelinesSafety Guidelines Electrical Equipment Guidelines Safety WarningsEthernet and Ethernet 10BASE-FL Overview Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage Parameter Ethernet Ieee 802.3 10BASE-FL SpecificationsIeee 802.3 10BASE-FL Specifications IeeeParameter Multimode What Is the 5EFL Port Adapter?What Is the 5EFL Port Adapter? Multimode Optical-Fiber ParametersTwo Port Adapters on a VIP2-50 Horizontal Orientation Shown Port Adapters in the Cisco 5EFL Port Adapter LEDsEthernet 10BASE-FL Fiber-Optic Cable Plug ST Type VIP2 and the 5EFL Port AdapterSram Dram Installing or Replacing a Port Adapter on a VIP2 Installing or Replacing a Port Adapter on a VIP2Screw Aligning a Port Adapter in a Port Adapter Slot VIP2 and the 5EFL Port Adapter Configuring the 5EFL Interfaces Attaching 5EFL Port Adapter Interface CablesAttaching 5EFL Port Adapter Interface Cables VIP2 and the 5EFL Port Adapter Configuring Interfaces Configuring the 5EFL InterfacesChecking the Configuration Using show Commands to Verify the VIP2 StatusStep Router# sh int e 3/0/0 Using show Commands to Display Interface InformationRouter# sh int e 3/1/0 Router# show version Router# show diag Using the ping CommandCisco 7200 Series and the 5EFL Port Adapter Cisco 7200 Series and the 5EFL Port AdapterRemoving a Port Adapter Handling a Port Adapter Guide Replacing a Port AdapterPort adapter Handle Attaching 5EFL Port Adapter Interface Cables Configuring the 5EFL Interfaces 10BASE-FL Interface Port Number Example Using show Commands to Verify the New Interface Status Router# sh int e 2/0 Cisco 7200 Series and the 5EFL Port Adapter StepLast reset from power-on Bridging software FF FF Configuring the 5EFL Interfaces Documentation CD-ROM Cisco Connection OnlineCisco Connection Online Documentation CD-ROM Documentation CD-ROM
Top Page Image Contents