Cisco Systems PA-2H manual Software and Hardware Requirements, Platform Minimum Cisco IOS Release

Page 16

Software and Hardware Requirements

Software and Hardware Requirements

Table 2-1 lists the minimum Cisco IOS software release required to use the 2H port adapters in supported router platforms.

Table 2-1

2H Port Adapter Software Requirements

 

 

 

Platform

 

Minimum Cisco IOS Release

 

 

Cisco 7000 series and Cisco 7500 series

 

 

 

 

•

With VIP2-15(=)

Cisco IOS Release 11.1(15)CA or a later release of Cisco IOS Release 11.1 CA

•

With VIP2-40(=)

Cisco IOS Release 11.1(15)CA or a later release of Cisco IOS Release 11.1 CA

•

With VIP2-50(=)

Cisco IOS Release 11.1(14)CA or a later release of Cisco IOS Release 11.1 CA

 

 

 

Cisco 7200 series

 

 

 

 

• Cisco 7204VXR, and Cisco 7206VXR

Cisco IOS Release 12.0(2)XE2 or a later release of Cisco IOS Release 12.0 XE

 

 

 

Cisco IOS Release 12.0(3)T or a later release of Cisco IOS Release 12.0 T

• Cisco 7204 and Cisco 7206

Cisco IOS Release 11.1(15)CA or a later release of Cisco IOS Release 11.1 CA

•

Cisco 7202

 

Cisco IOS Release 11.1(19)CC1 or a later release of Cisco IOS Release 11.1 CC

 

 

 

Cisco IOS Release 11.3(4)AA or a later release of Cisco IOS Release 11.3 AA

• Cisco 7206 router shelf

Cisco IOS Release 11.3(2)AA or a later release of Cisco IOS Release 11.3 AA

 

 

Cisco uBR7200 series

 

 

 

• Cisco uBR7246 and Cisco uBR7223

Cisco IOS Release 12.0(3)T or later release of Cisco IOS Release 12.0T

 

 

Catalyst 5000 family switches

 

 

 

 

•

With Catalyst RSM/VIP2-15(=)

Cisco IOS Release 11.2(15A)P or later release of Cisco IOS Release 11.2P

 

 

 

•

With Catalyst RSM/VIP2-40(=)

Cisco IOS Release 11.2(15A)P or later release of Cisco IOS Release 11.2P

 

 

 

 

Note In the Cisco 7200 series routers, there are specific configuration guidelines that must be observed for high-bandwidth port adapters such as the PA-2H Rev. B. For port adapter hardware and memory configuration guidelines for the Cisco 7200 series routers (including a Cisco 7206 as a router shelf in a Cisco AS5800 Universal Access Server), refer to the document, Cisco 7200 Series Port Adapter Hardware Configuration Guidelines , that shipped with your Cisco 7200 series router.

Caution The VIP2 requires that the host Cisco 7000 series router has the RSP7000 and RSP7000CI installed. The VIP2 will not operate properly with the Route Processor (RP), Switch Processor (SP), or Silicon Switch Processor (SSP) installed in the host Cisco 7000 series router.

Caution If you are using the HSSI dual-port adapter in the Catalyst 5000, 5500, 5505, or 5509 switch, you must install the port adapter on the Catalyst RSM/VIP2-15 or -40 Revision 2 (board part number 73-3468-XX, where XX is the version number). Do not use the HSSI dual-port adapter in the Catalyst 5000, 5505, or 5509 switch if you are installing it on a Catalyst RSM/VIP2-15 or -40 module that is not the Revision 2. If you fail to comply with this restriction, your system will shut down due to an overload of the power supply.

Caution You can only have two HSSI dual-port adapters per chassis when installed on a

Catalyst RSM/VIP2-15 or -40 module Revision 1 and used in the Catalyst 5500 switch.

2-2PA-2H Dual-Port HSSI Port Adapter Installation and Configuration

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved Document Objectives About This ManualDocument Organization Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM If You Need More InformationIf You Need More Information If You Need More Information If You Need More Information Overview Port Adapter Overview605559 LEDs Receptacles, Cables, and Pinouts Hssi Interface CableNull Modem Cable Connectors Hssi Null Modem CableReceptacles, Cables, and Pinouts Preparing for Installation List of Parts and ToolsSoftware and Hardware Requirements Platform Minimum Cisco IOS ReleaseSafety Guidelines Safety WarningsSafety Guidelines Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance Installation Overview VIP2 and the Dual-Port Hssi Port AdapterVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Removing a Port Adapter Location of Port Adapter Screw Partial Port Adapter ViewInstalling a Port Adapter Installing a New Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7200 Series and the Dual-Port Hssi Port Adapter Cisco 7206 with an Hssi Port Adapter in Port Adapter SlotPort adapter Handle Lever unlocked Position Replacing a Port Adapter Handling a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Cable Installation and Interface Configuration Attaching Hssi Port Adapter Interface CablesConnecting Hssi Cables Front View-PA-2H Shown without Handle Attaching a Null Modem CableConfiguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example Configuring Interfaces VIP2 PortsConfiguring Interfaces Configuring Cyclic Redundancy Checks Checking the ConfigurationUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Using the ping Command Router# pingConfiguring the Hssi Interfaces
Top Page Image Contents