Cisco Systems PA-2H manual Slot

Page 36

Installation Overview

Figure 5-4 Aligning the Port Adapter Metal Carrier Between the Slot Guides (Cisco 7206 shown)

Slot

6

H6597

5

guide

ETHERNET 10BT

ENABLED

LINK

RJ45

FAST ETHERNET

3

MII

4

0

1

SLOT

1

MII

FE

ENABLED

EJECT

SLOT

LINK

PCMCIA

EN

EN

0

MII

RJ45

RJ45

Note: This adapter alignment applies to any port or service adapter.

Step 4 With the metal carrier aligned in the slot guides, gently slide the port adapter half way into the slot.

Caution Do not slide the port adapter all the way into the slot until you have connected all required cables. Trying to do so will disrupt normal operation of the router.

Step 5 With the port adapter half way in the slot, connect all required cables to the port adapter.

Step 6 After connecting the cables, carefully slide the port adapter all the way into the slot until you feel the port adapter’s connectors seat in the midplane.

Step 7 Move the port adapter lever to the locked position. Figure 5-5 shows the port adapter lever in the locked position.

Note If the port adapter lever does not move to the locked position, the port adapter is not completely seated in the midplane. Carefully pull the port adapter half way out of the slot, reinsert it, and move the port adapter lever to the locked position.

5-4PA-2H Dual-Port HSSI Port Adapter Installation and Configuration

Image 36

Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved About This Manual Document ObjectivesDocument Organization Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM If You Need More InformationIf You Need More Information If You Need More Information If You Need More Information Overview Port Adapter Overview605559 LEDs Receptacles, Cables, and Pinouts Hssi Interface CableNull Modem Cable Connectors Hssi Null Modem CableReceptacles, Cables, and Pinouts Preparing for Installation List of Parts and ToolsSoftware and Hardware Requirements Platform Minimum Cisco IOS ReleaseSafety Guidelines Safety WarningsSafety Guidelines Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance Installation Overview VIP2 and the Dual-Port Hssi Port AdapterVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Removing a Port Adapter Location of Port Adapter Screw Partial Port Adapter ViewInstalling a Port Adapter Installing a New Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7200 Series and the Dual-Port Hssi Port Adapter Cisco 7206 with an Hssi Port Adapter in Port Adapter SlotPort adapter Handle Lever unlocked Position Replacing a Port Adapter Handling a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Cable Installation and Interface Configuration Attaching Hssi Port Adapter Interface CablesConnecting Hssi Cables Front View-PA-2H Shown without Handle Attaching a Null Modem CableConﬁguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example Conﬁguring Interfaces VIP2 PortsConfiguring Interfaces Conﬁguring Cyclic Redundancy Checks Checking the ConﬁgurationUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Using the ping Command Router# pingConfiguring the Hssi Interfaces