Cisco Systems PA-2H manual Catalyst RSM/VIP2 show Commands

Page 58

Configuring the HSSI Interfaces

Use the show controllers cbus command to display all the current interface processors and their interfaces. Following is an example of the show controller cbus command that shows the HSSI port 1/0/0 on a PA-2H HSSI port adapter installed on a VIP2 in interface processor slot 1:

Router# show controllers cbus

(additional displayed text omitted from this example)

slot1: VIP2, hw 2.3, sw 21.40, ccb 5800FF40, cmdq 48000090, vps 8192 software loaded from system

IOS (tm) VIP Software (SVIP-DW-M), Released Version 11.1(12)CA1 [biff 103] ROM Monitor version 17.0

HSSI-B(1) HW Revision 0x2, FW Revision 2.42 Hssi1/0/0, applique is Hssi DTE

received clockrate 51838976

gfreeq 48000160, lfreeq 48000200 (4480 bytes), throttled 0 rxlo 4, rxhi 258, rxcurr 0, maxrxcurr 0

txq 48001A80, txacc 48001A82 (value 129), txlimit 129

(additional displayed text omitted from this example)

Note For complete VIP2 command descriptions and examples, refer to the documentation resources listed in the “If You Need More Information” section on page vii.

Proceed to the section “Using the ping Command” to verify that each interface port is functioning properly.

Catalyst RSM/VIP2 show Commands

Caution If you are using the HSSI dual-port adapter in the Catalyst 5000, 5500, 5505, or 5509 switch, you must install the port adapter on the Catalyst RSM/VIP2-15 or -40 Revision 2 (board part number 73-3468-XX, where XX is the version number). Do not use the HSSI dual-port adapter in the Catalyst 5000, 5505, or 5509 switch if you are installing it on a Catalyst RSM/VIP2-15 or -40 module that is not the Revision 2. If you fail to comply with this restriction, your system will shut down due to an overload of the power supply.

Caution You can only have two HSSI dual-port adapters per chassis when installed on a

Catalyst RSM/VIP2-15 or -40 module Revision 1 and used in the Catalyst 5500 switch.

Following is an example of how the show interfaces [port-adapter/port] command displays status information (including the physical slot and port address) for the interfaces you specify. In this example, the PA-2H HSSI port adapter is in slot 0. (Interfaces are administratively shut down until you enable them.)

7-14PA-2H Dual-Port HSSI Port Adapter Installation and Configuration

Page 57 Page 59
Image 58
Page 57 Page 59
Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved Document Objectives About This ManualDocument Organization Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM If You Need More InformationIf You Need More Information If You Need More Information If You Need More Information Overview Port Adapter Overview605559 LEDs Receptacles, Cables, and Pinouts Hssi Interface CableNull Modem Cable Connectors Hssi Null Modem CableReceptacles, Cables, and Pinouts Preparing for Installation List of Parts and ToolsSoftware and Hardware Requirements Platform Minimum Cisco IOS ReleaseSafety Guidelines Safety WarningsSafety Guidelines Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance Installation Overview VIP2 and the Dual-Port Hssi Port AdapterVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Removing a Port Adapter Location of Port Adapter Screw Partial Port Adapter ViewInstalling a Port Adapter Installing a New Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7200 Series and the Dual-Port Hssi Port Adapter Cisco 7206 with an Hssi Port Adapter in Port Adapter SlotPort adapter Handle Lever unlocked Position Replacing a Port Adapter Handling a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Cable Installation and Interface Configuration Attaching Hssi Port Adapter Interface CablesConnecting Hssi Cables Front View-PA-2H Shown without Handle Attaching a Null Modem CableConfiguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example Configuring Interfaces VIP2 PortsConfiguring Interfaces Configuring Cyclic Redundancy Checks Checking the ConfigurationUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Using the ping Command Router# pingConfiguring the Hssi Interfaces
Top Page Image Contents