Cisco Systems PA-2H manual VIP2 and the Dual-Port Hssi Port Adapter, Installation Overview

Page 21

C H A P T E R 3

VIP2 and the Dual-Port HSSI

Port Adapter

This chapter describes the dual-port high-speed serial interface (HSSI) port adapter and its use on the VIP2 in Cisco 7200 series and Cisco 7500 series routers.

Installation Overview

The HSSI port adapter can be installed in either port adapter slot 0 or port adapter slot 1 on the VIP2. Figure 3-1 shows a VIP2 with PA-2H installed in port adapter slot 0.

Figure 3-1 VIP2-15 or VIP2-40 with PA-2H in Port Adapter Slot 0

Bus connector

SRAM

DIMM U5

PA-2H in port adapter slot 0

ENABLED

0

Port adapter handles not shown

CPU Boot ROM

U6

	DRAM
U2	SIMMs

U4

TD TC RD RC LB/C	1	HSSI		H10888
TD TC RD RC LB/C	1		CD
0			CD
1

Note Port adapters have a handle attached, but this handle is not shown to allow a full view of detail on each port adapter’s faceplate.

VIP2 and the Dual-Port HSSI Port Adapter 3-1

Image 21

Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved About This Manual Document ObjectivesDocument Organization Cisco Connection Online Cisco Connection OnlineIf You Need More Information Documentation CD-ROMIf You Need More Information If You Need More Information If You Need More Information Port Adapter Overview Overview605559 LEDs Hssi Interface Cable Receptacles, Cables, and PinoutsHssi Null Modem Cable Null Modem Cable ConnectorsReceptacles, Cables, and Pinouts List of Parts and Tools Preparing for InstallationPlatform Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesSafety Guidelines Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance VIP2 and the Dual-Port Hssi Port Adapter Installation OverviewVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Location of Port Adapter Screw Partial Port Adapter View Removing a Port AdapterInstalling a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7206 with an Hssi Port Adapter in Port Adapter Slot Cisco 7200 Series and the Dual-Port Hssi Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Replacing a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Attaching Hssi Port Adapter Interface Cables Cable Installation and Interface ConfigurationAttaching a Null Modem Cable Connecting Hssi Cables Front View-PA-2H Shown without HandleConﬁguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example VIP2 Ports Conﬁguring InterfacesConfiguring Interfaces Checking the Conﬁguration Conﬁguring Cyclic Redundancy ChecksUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Router# ping Using the ping CommandConfiguring the Hssi Interfaces