Cisco Systems PA-2H manual Ff Ff Ff Ff Ff Ff Ff Ff

Page 60

Configuring the HSSI Interfaces

Use the show diag command to determine which type of port adapter is installed on a

Catalyst RSM/VIP2 in your system. Specific port adapter information is displayed, as shown in the following example of a HSSI port adapter in slot (bay) 0:

Router# show

diag

0

 

 

 

 

 

 

 

Slot 0:

 

 

 

 

 

 

 

 

 

 

HSSI-B port adapter, 1

port

 

 

 

 

Port adapter

is analyzed

 

 

 

 

 

Port adapter

insertion time 2d13h ago

 

 

 

Hardware revision

1.17

 

 

Board revision

A0

Serial number

 

4518292

 

Part number

 

73-1801-05

Test history

 

0x0

 

 

RMA number

 

00-00-00

EEPROM format version 1

 

 

 

 

 

 

EEPROM contents (hex):

 

 

 

 

 

 

0x20:01

74 01

11

00

44

F1

94

49 07 09 05

00

00

00 00

0x30:50 00 00 00 97

04

21

00 FF FF FF FF FF FF FF FF

 

Slot

database information:

 

 

 

 

Flags: 0x4

 

Insertion time: 0x14E8 (3d00h ago)

VIP Controller Memory Size: Unknown

PA Bay 0 Information:

HSSI-B PA, 1 ports

EEPROM format version 1

HW rev 1.1, Board revision A0

Serial number: 04551053 Part number: 73-1801-05

Use the show controllers cbus command to display all the current interface processors and their interfaces. Following is an example of the show controller cbus command that shows the HSSI port 0/0 on a PA-2H HSSI port adapter installed in slot 0:

Router# show controllers cbus

(additional displayed text omitted from this example)

slot0: VIP2, hw 2.3, sw 21.40, ccb 5800FF40, cmdq 48000090, vps 8192 software loaded from system

IOS (tm) VIP Software (SVIP-DW-M), Released Version 11.1(12)CA1 [biff 103] ROM Monitor version 17.0

HSSI-B(1) HW Revision 0x2, FW Revision 2.42 Hssi1/0/0, applique is Hssi DTE

received clockrate 51838976

gfreeq 48000160, lfreeq 48000200 (4480 bytes), throttled 0 rxlo 4, rxhi 258, rxcurr 0, maxrxcurr 0

txq 48001A80, txacc 48001A82 (value 129), txlimit 129

(additional displayed text omitted from this example)

Note The slot values displayed by some commands (such as show diag and show controllers cbus) are not relevant to any physical connection; disregard these slot values for the Catalyst RSM/VIP2.

Note For complete Catalyst RSM/VIP2 command descriptions and examples, refer to the documentation resources listed in the “If You Need More Information” section on page vii.

Proceed to the section “Using the ping Command” to verify that each interface port is functioning properly.

7-16PA-2H Dual-Port HSSI Port Adapter Installation and Configuration

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved About This Manual Document ObjectivesDocument Organization Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM If You Need More InformationIf You Need More Information If You Need More Information If You Need More Information Overview Port Adapter Overview605559 LEDs Receptacles, Cables, and Pinouts Hssi Interface CableNull Modem Cable Connectors Hssi Null Modem CableReceptacles, Cables, and Pinouts Preparing for Installation List of Parts and ToolsSoftware and Hardware Requirements Platform Minimum Cisco IOS ReleaseSafety Guidelines Safety WarningsSafety Guidelines Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance Installation Overview VIP2 and the Dual-Port Hssi Port AdapterVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Removing a Port Adapter Location of Port Adapter Screw Partial Port Adapter ViewInstalling a Port Adapter Installing a New Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7200 Series and the Dual-Port Hssi Port Adapter Cisco 7206 with an Hssi Port Adapter in Port Adapter SlotPort adapter Handle Lever unlocked Position Replacing a Port Adapter Handling a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Cable Installation and Interface Configuration Attaching Hssi Port Adapter Interface CablesConnecting Hssi Cables Front View-PA-2H Shown without Handle Attaching a Null Modem CableConfiguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example Configuring Interfaces VIP2 PortsConfiguring Interfaces Configuring Cyclic Redundancy Checks Checking the ConfigurationUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Using the ping Command Router# pingConfiguring the Hssi Interfaces
Top Page Image Contents