Cisco Systems PA-2H manual Port adapters Port adapter lever in unlocked position

Page 41

Removing a Port Adapter

Figure 6-3 Placing the Port Adapter Lever in the Unlocked Position (Cisco uBR7223 Shown)

Port adapters

Port adapter lever in unlocked position

16217

Step 3 Grasp the handle on the port adapter and pull the port adapter from the midplane, about half way out of its slot. If you are removing a blank port adapter, pull the blank port adapter from the chassis slot.

Note As you disengage the port adapter from the router midplane, OIR administratively shuts down all active interfaces on the port adapter.

Step 4 With the port adapter half way out of the slot, disconnect all cables from the port adapter.

Step 5 After disconnecting the cables, pull the port adapter from its chassis slot.

Caution Always handle the port adapter by the carrier edges and handle; never touch the port adapter’s components or connector pins. (Refer to Figure 6-4.)

Figure 6-4 Handling a Port Adapter

Metal carrier

Printed circuit board

H6420

Step 6 Place the port adapter on an antistatic surface with its components facing upward, or in a static shielding bag. If the port adapter will be returned to the factory, immediately place it in a static shielding bag.

This completes the procedure for removing a port adapter from a Cisco uBR7200 series router.

Cisco uBR7200 Series and the Dual-Port HSSI Port Adapter 6-3

Image 41

Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved Document Organization About This ManualDocument Objectives Cisco Connection Online Cisco Connection OnlineIf You Need More Information Documentation CD-ROMIf You Need More Information If You Need More Information If You Need More Information Port Adapter Overview Overview605559 LEDs Hssi Interface Cable Receptacles, Cables, and PinoutsHssi Null Modem Cable Null Modem Cable ConnectorsReceptacles, Cables, and Pinouts List of Parts and Tools Preparing for InstallationPlatform Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesSafety Guidelines Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesElectrical Equipment Guidelines FCC Class B Compliance VIP2 and the Dual-Port Hssi Port Adapter Installation OverviewVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Location of Port Adapter Screw Partial Port Adapter View Removing a Port AdapterInstalling a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7206 with an Hssi Port Adapter in Port Adapter Slot Cisco 7200 Series and the Dual-Port Hssi Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Replacing a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Attaching Hssi Port Adapter Interface Cables Cable Installation and Interface ConfigurationAttaching a Null Modem Cable Connecting Hssi Cables Front View-PA-2H Shown without HandleConﬁguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example VIP2 Ports Conﬁguring InterfacesConfiguring Interfaces Checking the Conﬁguration Conﬁguring Cyclic Redundancy ChecksUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Router# ping Using the ping CommandConfiguring the Hssi Interfaces