Cisco Systems PA-2H manual Router# show version

Page 59

Checking the Configuration

Router# show interfaces h 0/0 Hssi0/0 is up, line protocol is up Hardware is HSSI-B

Internet address is 5.8.1.1/24

MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, rely 255/255, load 1/255 Encapsulation HDLC, loopback not set, keepalive not set

Last input 2d22h, output 00:00:19, output hang never Last clearing of “show interface” counters 2d20h Queueing strategy: fifo

Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec

5 minute output rate 0 bits/sec, 0 packets/sec

0 packets input, 0 bytes, 0 no buffer

Received 0 broadcasts, 0 runts, 0 giants, 0 parity

0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 4084 packets output, 1298712 bytes, 0 underruns

0 output errors, 0 applique, 0 interface resets

0 output buffer failures, 0 output buffers swapped out

0 carrier transitions

Use the show version command to display the conﬁguration of the system hardware (the number of each interface processor type installed), the software version, the names and sources of conﬁguration ﬁles, and the boot images.

Following is an example of the show version command :

Router# show version

Cisco Internetwork Operating System Software

IOS (tm) GS Software (C5RSM-JV-MZ), Version 11.1(12)CA1

Copyright (c) 1986-1995 by cisco Systems, Inc.

Compiled Fri 06-Oct-95 12:22 by mpo

Image text-base: 0x600088A0, data-base: 0x605A4000

ROM: System Bootstrap, Version 5.3(5)

ROM: GS Bootstrap Software (RSP-BOOT-M), Version 11.1(12), RELEASED SOFTWARE

Router uptime is 4 hours, 22 minutes

System restarted by reload

System image file is “slot0:c5rsm-jv-mz”, booted via slot0

cisco RSP2 (R4700) processor with 16384K bytes of memory. R4600 processor, Implementation 32, Revision 2.0

Last reset from power-on G.703/E1 software, Version 1.0. Bridging software.

X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. Chassis Interface.

1 VIP2 controllers (2 HSSI).

2 HSSI network interfaces.

125K bytes of non-volatile configuration memory.

20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K). 8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x2

Cable Installation and Interface Configuration 7-15

Image 59

Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved Document Organization About This ManualDocument Objectives Cisco Connection Online Cisco Connection OnlineIf You Need More Information Documentation CD-ROMIf You Need More Information If You Need More Information If You Need More Information Port Adapter Overview Overview605559 LEDs Hssi Interface Cable Receptacles, Cables, and PinoutsHssi Null Modem Cable Null Modem Cable ConnectorsReceptacles, Cables, and Pinouts List of Parts and Tools Preparing for InstallationPlatform Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesSafety Guidelines Preventing Electrostatic Discharge Damage Telephone Wiring GuidelinesElectrical Equipment Guidelines FCC Class B Compliance VIP2 and the Dual-Port Hssi Port Adapter Installation OverviewVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Location of Port Adapter Screw Partial Port Adapter View Removing a Port AdapterInstalling a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7206 with an Hssi Port Adapter in Port Adapter Slot Cisco 7200 Series and the Dual-Port Hssi Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Replacing a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Attaching Hssi Port Adapter Interface Cables Cable Installation and Interface ConfigurationAttaching a Null Modem Cable Connecting Hssi Cables Front View-PA-2H Shown without HandleConﬁguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example VIP2 Ports Conﬁguring InterfacesConfiguring Interfaces Checking the Conﬁguration Conﬁguring Cyclic Redundancy ChecksUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Router# ping Using the ping CommandConfiguring the Hssi Interfaces