Cisco Systems PA-2H manual Use the show diag command to display the hardware revision

Page 55

Checking the Configuration

Use the show version command to display the conﬁguration of the system hardware (the number of each port adapter type installed), the software version, the names and sources of conﬁguration ﬁles, and the boot images. Following is an example of the output from the show version command:

Router# show version

Cisco Internetwork Operating System Software

IOS (tm) 7200 Software (C7200-J-M), Version 11.1(12)CA1

Copyright (c) 1986-1996 by cisco Systems, Inc.

Compiled Fri 09-Aug-96 21:14 by biff

Image text-base: 0x60010890, data-base: 0x605F0000

ROM: System Bootstrap, Version 11.1(12)CA1, RELEASED SOFTWARE

ROM: 7200 Software (C7200-J-M), Version 11.1(12)CA1, RELEASED SOFTWARE

Router uptime is 23 hours System restarted by reload

System image file is “biff/c7200-j-mz”, booted via tftp from 1.1.1.254

cisco 7200 (R4700) processor with 22528K/10240K bytes of memory. R4700 processor, Implementation 33, Revision 1.0 (Level 2 Cache) Last reset from power-on

Bridging software.

SuperLAT software copyright 1990 by Meridian Technology Corp). X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. TN3270 Emulation software (copyright 1994 by TGV Inc).

(additional display text omitted from this example)

1 HSSI network interfaces.

125K bytes of non-volatile configuration memory.

8192K bytes of Flash internal SIMM (Sector size 256K). Configuration register is 0x0

Use the show diag slot command to determine which type of port adapter is installed in your system. Speciﬁc port adapter information is displayed, as shown in the following example of a PA-2H HSSI port adapter in port adapter slot 2:

Router# show diag 2
Slot 2:
HSSI-B port adapter, 1				port
Port adapter is analyzed
Port adapter insertion				time 2d13h ago
Hardware revision			1.1		Board revision			A0
Serial number			4518292		Part number			73-1801-05
Test history			0x0		RMA number			00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01	74	01 01 00		44	F1 94 49 07	09	05 00	00 00	00
0x30: 50 00 00 00 97				04	21 00 FF FF FF FF FF			FF FF FF

Note Port adapters used with the 7200 VXR routers require the correct base hardware revision in order to function. The following error message will occur on bootup if the incorrect hardware revision is used:

PA-3-REVNOTSUPPORTED:PA in slot 1 (Ethernet) requires base h/w revision of (1.14)

for this chassis

Use the show diag command to display the hardware revision.

Cable Installation and Interface Configuration 7-11

Image 55

Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved Document Objectives About This ManualDocument Organization Cisco Connection Online Cisco Connection OnlineIf You Need More Information Documentation CD-ROMIf You Need More Information If You Need More Information If You Need More Information Port Adapter Overview Overview605559 LEDs Hssi Interface Cable Receptacles, Cables, and PinoutsHssi Null Modem Cable Null Modem Cable ConnectorsReceptacles, Cables, and Pinouts List of Parts and Tools Preparing for InstallationPlatform Minimum Cisco IOS Release Software and Hardware RequirementsSafety Warnings Safety GuidelinesSafety Guidelines Electrical Equipment Guidelines Telephone Wiring GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance VIP2 and the Dual-Port Hssi Port Adapter Installation OverviewVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Location of Port Adapter Screw Partial Port Adapter View Removing a Port AdapterInstalling a New Port Adapter Installing a Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7206 with an Hssi Port Adapter in Port Adapter Slot Cisco 7200 Series and the Dual-Port Hssi Port AdapterPort adapter Handle Lever unlocked Position Handling a Port Adapter Replacing a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Attaching Hssi Port Adapter Interface Cables Cable Installation and Interface ConfigurationAttaching a Null Modem Cable Connecting Hssi Cables Front View-PA-2H Shown without HandleConﬁguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example VIP2 Ports Conﬁguring InterfacesConfiguring Interfaces Checking the Conﬁguration Conﬁguring Cyclic Redundancy ChecksUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Router# ping Using the ping CommandConfiguring the Hssi Interfaces