Cisco Systems PA-2H manual Cisco 7200 Series and Cisco uBR7200 Series show Commands

Page 54

Configuring the HSSI Interfaces

Cisco 7200 Series and Cisco uBR7200 Series show Commands

Following is an example of how the show interfaces [type slot/port] command displays status information (including the physical slot and port address) for the interfaces you specify. The following example of the show interfaces hssi type slot/port command shows all of the information specific to the PA-2H HSSI port adapter in port adapter slot 2. (Interfaces are administratively shut down until you enable them.)

Router# show int h 2/0

Hssi2/0 is up, line protocol is up

Hardware is HSSI-B

Internet address is 2.8.1.2/24

MTU 4470 bytes, BW 45045 Kbit, DLY 200 usec, rely 252/255, load 1/255

Encapsulation HDLC, loopback not set, keepalive not set

Last

input never, output never, output hang never

Last

clearing of “show interface”

counters never

Queueing strategy: fifo

 

 

 

Output queue 0/40, 0

drops; input

queue 0/75, 0 drops

5 minute input rate 0 bits/sec, 0

packets/sec

5 minute output rate

0 bits/sec, 0 packets/sec

0

packets input, 0 bytes,

0 no

buffer

Received 0 broadcasts, 0 runts, 0

giants

 

0 parity

 

 

 

 

1

input errors, 1

CRC, 0 frame, 1

overrun, 0 ignored, 0 abort

1

packets output,

24 bytes, 0 underruns

0

output errors, 0 applique, 1

interface resets

0

output buffer failures,

0 output buffers swapped out

0

carrier transitions

TM=down

CA=up LC=down

Note For the Cisco 7206 and Cisco 7206VXR router shelves, the show interfaces command requires a shelf number in the format show interfaces type shelf number/port adapter slot/interface.

Following is an example of the show controllers type slot/port command that shows information about a specific PA-2H HSSI port adapter:

Router# show controllers hssi 2/0

(additional display text omitted from this example)

HSSI-B: show controller:

PAS unit 0, subunit 0, f/w version 2-42, rev ID 0x2800001, version 2 idb = 0x60BDE9B0, ds = 0x60BE0740, ssb=0x60BE090C

Clock mux=0x35, ucmd_ctrl=0x8, port_status=0x25 Serial config=0x8, line config=0x1B0202 maxdgram=4474, bufpool=128Kb, 256 particles

TM=down CA=up LC=down

line state: up

HSSI DTE cable, received clockrate 51838976

base0 registers=0x3D800000, base1 registers=0x3D802000

mxt_ds=0x60C34D1C, rx ring entries=128, tx ring entries=256 rxring=0x4B05FCC0, rxr shadow=0x60BE0A2C, rx_head=1 txring=0x4B060140, txr shadow=0x60BE1054, tx_head=0, tx_tail=0, tx_count=0 throttled=0, enabled=0, disabled=0

rx_no_eop_err=0, rx_no_stp_err=0, rx_no_eop_stp_err=0 rx_no_buf=0, rx_soft_overrun_err=0 tx_underrun_err=0, tx_soft_underrun_err=0, tx_limited=0 tx_fullring=0, tx_started=50

7-10PA-2H Dual-Port HSSI Port Adapter Installation and Configuration

Page 53 Page 55
Image 54
Page 53 Page 55
Contents Corporate Headquarters Copyright 1996-1999, Cisco Systems, Inc All rights reserved About This Manual Document ObjectivesDocument Organization Cisco Connection Online Cisco Connection OnlineDocumentation CD-ROM If You Need More InformationIf You Need More Information If You Need More Information If You Need More Information Overview Port Adapter Overview605559 LEDs Receptacles, Cables, and Pinouts Hssi Interface CableNull Modem Cable Connectors Hssi Null Modem CableReceptacles, Cables, and Pinouts Preparing for Installation List of Parts and ToolsSoftware and Hardware Requirements Platform Minimum Cisco IOS ReleaseSafety Guidelines Safety WarningsSafety Guidelines Telephone Wiring Guidelines Electrical Equipment GuidelinesPreventing Electrostatic Discharge Damage FCC Class B Compliance Installation Overview VIP2 and the Dual-Port Hssi Port AdapterVIP2-50 with Two Hssi Port Adapters in Port Adapter Slots 0 Removing a Port Adapter Location of Port Adapter Screw Partial Port Adapter ViewInstalling a Port Adapter Installing a New Port AdapterInstalling a Port Adapter Installation Overview Catalyst RSM/VIP2 and the Dual-Port Hssi Port Adapter Catalyst RSM/VIP2-40 with PA-2H in Port Adapter Slot Removing a Port Adapter Installing a Port Adapter Installing a New Port Adapter Installation Overview Cisco 7200 Series and the Dual-Port Hssi Port Adapter Cisco 7206 with an Hssi Port Adapter in Port Adapter SlotPort adapter Handle Lever unlocked Position Replacing a Port Adapter Handling a Port AdapterSlot Port adapter Installation Overview Cisco uBR7200 Series Dual-Port Hssi Port Adapter Port adapters Port adapters Port adapter lever in unlocked position Inside slot guide PC board Metal carrier Port adapter retention clip in locked position Installation Overview Cable Installation and Interface Configuration Attaching Hssi Port Adapter Interface CablesConnecting Hssi Cables Front View-PA-2H Shown without Handle Attaching a Null Modem CableConfiguring the Hssi Interfaces Cisco 7200 Series and Cisco uBR7200 Series Ports Cisco 7206 Hssi Port Number Example Configuring Interfaces VIP2 PortsConfiguring Interfaces Configuring Cyclic Redundancy Checks Checking the ConfigurationUsing show Commands to Verify the New Interface Status Cisco 7200 Series and Cisco uBR7200 Series show Commands Use the show diag command to display the hardware revision VIP2 show Commands FF FF FF FF FF FF FF FF Catalyst RSM/VIP2 show Commands Router# show version FF FF FF FF FF FF FF FF Using the ping Command Router# pingConfiguring the Hssi Interfaces
Top Page Image Contents