Cisco Systems manual Installing the Cisco AS5350XM Universal Gateway, Setting Up the Chassis

Page 33

C H A P T E R 3

Installing the Cisco AS5350XM Universal

Gateway

This chapter guides you through the installation of the Cisco AS5350XM universal gateway and includes the following sections:

•Setting Up the Chassis, page 3-1

•Connecting to the Network, page 3-6

•Connecting to the Console and Auxiliary Ports, page 3-11

•Connecting a Signal Generator to the BITS Port, page 3-12

•Connecting an Alarm to the Alarm Port, page 3-13

•Supplying Power, page 3-13

•Where to Go Next, page 3-18

Warning Only trained and qualified personnel should be allowed to install or replace this equipment. Statement 49

Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use. Statement 39

Warning Incorrect connection of this or connected equipment to a general purpose outlet could result in a hazardous situation. Statement 87

Setting Up the Chassis

You can set the chassis on a desktop or install it in a rack. Use the procedure in this section that best meets the needs of your network:

•Setting the Chassis on a Desktop

•Rack-Mounting the Chassis

Cisco AS5350XM Universal Gateway Chassis Installation Guide

 

OL-6417-02

3-1

 

 

 

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Cisco AS5350XM Universal Gateway Chassis Installation Guide Cisco AS5350XM Universal Gateway Chassis Installation Guide Iii N T E N T SInstalling the Cisco AS5350XM Universal Gateway Overview B-1 OL-6417-02 Vii Document OrganizationViii Document ConventionsBewaar Deze Instructies Bewahren SIE Diese Hinweise GUT AUF Spara Dessa Anvisningar Xii GEM Disse AnvisningerXiii Cisco.com Obtaining DocumentationProduct Documentation DVD XivOrdering Documentation Documentation FeedbackReporting Security Problems in Cisco Products Cisco Product Security OverviewXvi Obtaining Technical Assistance Submitting a Service RequestCisco Technical Support & Documentation Website XviiDefinitions of Service Request Severity Obtaining Additional Publications and InformationXviii Xix OL-6417-02 Chassis Components OverviewCisco AS5350XM Universal Gateway Front Panel Product Serial Number LocationCisco Product Identification Tool Dial Feature Cards DFCsChassis Specifications Power SupplySee the Regulatory Compliance and Safety OL-6417-02 Maintaining Safety with Electricity Safety RecommendationsPreventing Electrostatic Discharge Damage Preparing to Connect to a Network Required Tools and EquipmentConsole and Auxiliary Ports Ethernet ConnectionsAlarm Port 2T Serial PortsBits Port Power Supply Considerations Setting Up the Chassis Installing the Cisco AS5350XM Universal GatewayAttaching the Rubber Feet Setting the Chassis on a DesktopAttaching the Rubber Feet Rack-Mounting the ChassisRequired Tools and Equipment Installing in a Rack Connecting to an Ethernet Network Connecting to the NetworkConnecting to an Ethernet Hub 10/100BASE-T Shown Connecting to a WANConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack 10 Connecting an 8-Port DFC to an RJ-45 Jack Connecting to the Console Port Connecting to the Console and Auxiliary PortsConnecting a Modem to the Auxiliary Port Connecting a Signal Generator to the Bits PortSupplying Power Connecting an Alarm to the Alarm PortConnecting the AC Power Cord 16 Connecting the AC Power Cord Wiring the DC Power Supply18 DC Power Supply Connections-Single Power Supply 19 DC Power Supply Connections-Redundant Power Supply Where to Go Next LEDs TroubleshootingLED Monitoring the EnvironmentCisco AS5350XM Universal Gateway Slot Numbering Displaying the Environment StatusPower Supply Troubleshooting Network Interfaces Replacing the Fan TrayRemoving the Fan Tray Cisco AS5350XM Front Panel Pulling the Edge of the Fan Tray Slide Metal Tabs out of the Slots Installing the Fan TrayInserting the Metal Tabs into the Slots 10 Tightening Fan Tray Screws Getting HelpSafety Recommendations Removing the Chassis CoverRequired Tools Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Replacing the Compact Flash AUX CON GE1 GE0 Replacing DIMMs Required Tools and EquipmentReplacing the Dimm Figure A-4 Removing and Replacing the Dimm Medium Phillips screwdriver Five screws Replacing the Chassis CoverFigure A-6 Replacing the Chassis Cover Chassis Cover ReplacementFigure A-7 Cisco AS5350XM Chassis Overview Replacing the Power SupplyRequired Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Figure B-3 Removing the Chassis Cover Screws Removing the Old Power Supply Figure B-7 Removing the Air Separator Figure B-8 Power Supply Connectors Figure B-10 Lifting the Power Supply Out of the Chassis Installing the Power SupplyFigure B-11 Inserting the Power Supply in the Chassis Figure B-13 Replacing the Air Separator Secure the chassis cover with five screws Connect the DC connector to the rear of the power supply To DC source DC connector Page OL-6417-02 Console and Auxiliary Port Cables and Pinouts Cabling SpecificationsConsole Port Cables and Pinouts Identifying a Rollover CableRJ-45-to-DB-9 Auxiliary Port Cables and Pinouts Ethernet Port PinoutsAlarm Port Pinouts Bits Port PinoutsBantam Jack Port Pinouts OL-6417-02 IN-1 NumericsIN-2 WANIN-3 IN-4 IN-5 IN-6
Related manuals
Manual 104 pages 52.67 Kb Manual 6 pages 52.67 Kb
Top Page Image Contents