Cisco Systems AS5350XM manual Installing the Fan Tray, Slide Metal Tabs out of the Slots

Page 58

Chapter 4 Troubleshooting

Replacing the Fan Tray

Figure 4-7 Slide Metal Tabs out of the Slots

Tabs

3

3

35705

Installing the Fan Tray

To install the fan tray, follow this procedure:

Step 1 Insert the metal tabs located at the end of the fan tray into their slots. (See Figure 4-8.) Use your left hand to hold that end of the fan tray against the chassis to ensure that the metal tabs do not slip out of their slots.

Cisco AS5350XM Universal Gateway Chassis Installation Guide

4-8	OL-6417-02

Image 58

Contents Cisco AS5350XM Universal Gateway Chassis Installation Guide Cisco AS5350XM Universal Gateway Chassis Installation Guide N T E N T S IiiInstalling the Cisco AS5350XM Universal Gateway Overview B-1 OL-6417-02 Document Organization ViiDocument Conventions ViiiBewaar Deze Instructies Bewahren SIE Diese Hinweise GUT AUF Spara Dessa Anvisningar GEM Disse Anvisninger XiiXiii Product Documentation DVD Obtaining DocumentationCisco.com XivDocumentation Feedback Ordering DocumentationCisco Product Security Overview Reporting Security Problems in Cisco ProductsXvi Cisco Technical Support & Documentation Website Submitting a Service RequestObtaining Technical Assistance XviiObtaining Additional Publications and Information Definitions of Service Request SeverityXviii Xix OL-6417-02 Overview Chassis ComponentsProduct Serial Number Location Cisco AS5350XM Universal Gateway Front PanelDial Feature Cards DFCs Cisco Product Identification ToolPower Supply Chassis SpecificationsSee the Regulatory Compliance and Safety OL-6417-02 Safety Recommendations Maintaining Safety with ElectricityPreventing Electrostatic Discharge Damage Required Tools and Equipment Preparing to Connect to a NetworkEthernet Connections Console and Auxiliary Ports2T Serial Ports Alarm PortBits Port Power Supply Considerations Installing the Cisco AS5350XM Universal Gateway Setting Up the ChassisSetting the Chassis on a Desktop Attaching the Rubber FeetRack-Mounting the Chassis Attaching the Rubber FeetRequired Tools and Equipment Installing in a Rack Connecting to the Network Connecting to an Ethernet NetworkConnecting to a WAN Connecting to an Ethernet Hub 10/100BASE-T ShownConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack 10 Connecting an 8-Port DFC to an RJ-45 Jack Connecting to the Console and Auxiliary Ports Connecting to the Console PortConnecting a Signal Generator to the Bits Port Connecting a Modem to the Auxiliary PortConnecting an Alarm to the Alarm Port Supplying PowerConnecting the AC Power Cord Wiring the DC Power Supply 16 Connecting the AC Power Cord18 DC Power Supply Connections-Single Power Supply 19 DC Power Supply Connections-Redundant Power Supply Where to Go Next Troubleshooting LEDsMonitoring the Environment LEDDisplaying the Environment Status Cisco AS5350XM Universal Gateway Slot NumberingPower Supply Replacing the Fan Tray Troubleshooting Network InterfacesRemoving the Fan Tray Cisco AS5350XM Front Panel Pulling the Edge of the Fan Tray Installing the Fan Tray Slide Metal Tabs out of the SlotsInserting the Metal Tabs into the Slots Getting Help 10 Tightening Fan Tray ScrewsRemoving the Chassis Cover Safety RecommendationsRequired Tools Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Replacing the Compact Flash AUX CON GE1 GE0 Required Tools and Equipment Replacing DIMMsReplacing the Dimm Figure A-4 Removing and Replacing the Dimm Replacing the Chassis Cover Medium Phillips screwdriver Five screwsChassis Cover Replacement Figure A-6 Replacing the Chassis CoverFigure A-7 Cisco AS5350XM Chassis Replacing the Power Supply OverviewRequired Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Figure B-3 Removing the Chassis Cover Screws Removing the Old Power Supply Figure B-7 Removing the Air Separator Figure B-8 Power Supply Connectors Installing the Power Supply Figure B-10 Lifting the Power Supply Out of the ChassisFigure B-11 Inserting the Power Supply in the Chassis Figure B-13 Replacing the Air Separator Secure the chassis cover with five screws Connect the DC connector to the rear of the power supply To DC source DC connector Page OL-6417-02 Cabling Specifications Console and Auxiliary Port Cables and PinoutsIdentifying a Rollover Cable Console Port Cables and PinoutsRJ-45-to-DB-9 Ethernet Port Pinouts Auxiliary Port Cables and PinoutsBits Port Pinouts Alarm Port PinoutsBantam Jack Port Pinouts OL-6417-02 Numerics IN-1WAN IN-2IN-3 IN-4 IN-5 IN-6

Related manuals

Manual 104 pages 52.67 Kb

Manual 6 pages 52.67 Kb