Cisco Systems AS5350XM manual Required Tools and Equipment

Page 36

Chapter 3 Installing the Cisco AS5350XM Universal Gateway

Setting Up the Chassis

Required Tools and Equipment

You need the following tools and equipment to rack-mount the chassis:

Number 2 Phillips screwdriver (not included)

Medium flat-blade screwdriver (not included)

Screws for attaching the chassis to the rack (not included)

Standard rack-mount brackets (included)

Screws for attaching the brackets to the chassis (included)

Figure 3-2 Standard Rack-Mount Brackets

Bracket for 19-inch rack

Bracket for 23-inch rack

36012

Attaching the Brackets

To attach the mounting brackets to the chassis, follow this procedure:

Step 1 Set the chassis on a flat surface. (See Figure 3-3.)

Note The chassis may be installed with either the front or rear panel facing forward.

Step 2 Attach the standard 19- (48.26-) or 23-inch (58.42-cm) rack brackets to the sides of the chassis. Use the screws provided with the mounting brackets. (See Figure 3-3.)

Note There are three sets of mounting holes on the sides of the chassis. Attach the brackets for front, rear, or middle mounting.

Figure 3-3 Standard Bracket Installation—Front Panel Forward

35669

Note: The second bracket attaches to the other side of the chassis.

The chassis can also be installed with the rear panel forward.

Cisco AS5350XM Universal Gateway Chassis Installation Guide

3-4

OL-6417-02

 

 

Image 36
Contents Cisco AS5350XM Universal Gateway Chassis Installation Guide Cisco AS5350XM Universal Gateway Chassis Installation Guide N T E N T S IiiInstalling the Cisco AS5350XM Universal Gateway Overview B-1 OL-6417-02 Document Organization ViiDocument Conventions ViiiBewaar Deze Instructies Bewahren SIE Diese Hinweise GUT AUF Spara Dessa Anvisningar GEM Disse Anvisninger XiiXiii Obtaining Documentation Cisco.comProduct Documentation DVD XivDocumentation Feedback Ordering DocumentationReporting Security Problems in Cisco Products Cisco Product Security OverviewXvi Submitting a Service Request Obtaining Technical AssistanceCisco Technical Support & Documentation Website XviiDefinitions of Service Request Severity Obtaining Additional Publications and InformationXviii Xix OL-6417-02 Overview Chassis ComponentsProduct Serial Number Location Cisco AS5350XM Universal Gateway Front PanelDial Feature Cards DFCs Cisco Product Identification ToolPower Supply Chassis SpecificationsSee the Regulatory Compliance and Safety OL-6417-02 Safety Recommendations Maintaining Safety with ElectricityPreventing Electrostatic Discharge Damage Required Tools and Equipment Preparing to Connect to a NetworkEthernet Connections Console and Auxiliary PortsAlarm Port 2T Serial PortsBits Port Power Supply Considerations Installing the Cisco AS5350XM Universal Gateway Setting Up the ChassisSetting the Chassis on a Desktop Attaching the Rubber FeetRack-Mounting the Chassis Attaching the Rubber FeetRequired Tools and Equipment Installing in a Rack Connecting to the Network Connecting to an Ethernet NetworkConnecting to a WAN Connecting to an Ethernet Hub 10/100BASE-T ShownConnecting a 2-Port or 4-Port DFC to an RJ-45 T1 Jack Connecting a 2-Port or 4-Port DFC to an RJ-45 Jack 10 Connecting an 8-Port DFC to an RJ-45 Jack Connecting to the Console and Auxiliary Ports Connecting to the Console PortConnecting a Signal Generator to the Bits Port Connecting a Modem to the Auxiliary PortConnecting an Alarm to the Alarm Port Supplying PowerConnecting the AC Power Cord Wiring the DC Power Supply 16 Connecting the AC Power Cord18 DC Power Supply Connections-Single Power Supply 19 DC Power Supply Connections-Redundant Power Supply Where to Go Next Troubleshooting LEDsMonitoring the Environment LEDDisplaying the Environment Status Cisco AS5350XM Universal Gateway Slot NumberingPower Supply Troubleshooting Network Interfaces Replacing the Fan TrayRemoving the Fan Tray Cisco AS5350XM Front Panel Pulling the Edge of the Fan Tray Installing the Fan Tray Slide Metal Tabs out of the SlotsInserting the Metal Tabs into the Slots Getting Help 10 Tightening Fan Tray ScrewsSafety Recommendations Removing the Chassis CoverRequired Tools Chassis Cover Removal Figure A-1 Removing the Chassis Cover Screws Replacing the Compact Flash AUX CON GE1 GE0 Replacing DIMMs Required Tools and EquipmentReplacing the Dimm Figure A-4 Removing and Replacing the Dimm Replacing the Chassis Cover Medium Phillips screwdriver Five screwsChassis Cover Replacement Figure A-6 Replacing the Chassis CoverFigure A-7 Cisco AS5350XM Chassis Replacing the Power Supply OverviewRequired Tools and Equipment Figure B-1 DC Power Supply Connections-Single Power Supply To DC source DC connector Figure B-3 Removing the Chassis Cover Screws Removing the Old Power Supply Figure B-7 Removing the Air Separator Figure B-8 Power Supply Connectors Installing the Power Supply Figure B-10 Lifting the Power Supply Out of the ChassisFigure B-11 Inserting the Power Supply in the Chassis Figure B-13 Replacing the Air Separator Secure the chassis cover with five screws Connect the DC connector to the rear of the power supply To DC source DC connector Page OL-6417-02 Cabling Specifications Console and Auxiliary Port Cables and PinoutsIdentifying a Rollover Cable Console Port Cables and PinoutsRJ-45-to-DB-9 Ethernet Port Pinouts Auxiliary Port Cables and PinoutsAlarm Port Pinouts Bits Port PinoutsBantam Jack Port Pinouts OL-6417-02 Numerics IN-1WAN IN-2IN-3 IN-4 IN-5 IN-6
Related manuals
Manual 104 pages 52.67 Kb Manual 6 pages 52.67 Kb