Cisco Systems 78-13983-04 manual Obtaining Technical Assistance, Documentation CD-ROM

Page 10

About This Guide

Obtaining Technical Assistance

Documentation CD-ROM

Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.

Ordering Documentation

Cisco documentation is available in the following ways:

•Registered Cisco Direct Customers can order Cisco Product documentation from the Networking Products MarketPlace:

http://www.cisco.com/cgi-bin/order/order_root.pl

•Registered Cisco.com users can order the Documentation CD-ROM through the online Subscription Store:

http://www.cisco.com/go/subscription

•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, in North America, by calling 800 553-NETS(6387).

Documentation Feedback

If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.

You can e-mail your comments to bug-doc@cisco.com.

To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:

Cisco Systems, Inc.

Document Resource Connection

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Obtaining Technical Assistance

Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	x	78-13983-04

Image 10

Contents Corporate Headquarters Customer Order Number DOC-7813983= Text Part NumberCopyright 2002 Cisco Systems, Inc All rights reserved About This Guide Software FeaturesLimitations and Restrictions First-Time Configuration AudienceConfiguring PIM Using the Setup Command FacilitySaving Configuration Changes Configuring PPP MultiplexingMode y-cable Configuring RedundancyWhere to Go Next Assigning a QoS Boilerplate to an InterfacePage Organization ObjectivesAudience Chapter Title DescriptionBoldface font Document ConventionsConvention Description Boldface screenObtaining Documentation Additional InformationRelated Documentation World Wide WebOrdering Documentation Obtaining Technical AssistanceDocumentation CD-ROM Documentation FeedbackCisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Overview of the MWR BenefitsNetwork Processor Software Software FeaturesCisco IOS Software MLP, PPP Control Path IPCP, NCP, LCP, ClnsPPP Multiplexing/Demultiplexing RTP/UDP Header CompressionRedundancy Support RTP Header CompressionRFC1213-MIB MIB SupportMWR 1900 supports the following MIBs RFC1253-MIBLimitations and Restrictions 802.1Q VLANs Frame Relay FRBefore You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Viewing the configuration Enter a host name for the router this example usesYou are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed Where to Go Next First-Time Configuration Where to Go NextCisco IOS Software Basics Getting HelpExit , or logout Understanding Command ModesConfigure terminal As interface serial 0/0Undoing a Command or Feature Saving Configuration ChangesPage Configuring with the Command-Line Interface Prompt changes to Routerconfig# Configuring the Host Name and PasswordEnter global configuration mode Verifying the Version of Cisco IOS SoftwareExit interface configuration mode Configuring Loopback InterfacesExit to global configuration mode Change the name of the router to a meaningful nameConfiguring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation To set the default PPP protocol ID, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the maximum length of the subframe, enterRPM-3config-if#ip rtp header-compression Configuring T1 and E1 Interfaces Configuring T1 InterfacesConfiguring E1 Interfaces Set the carrier delay for the serial interfaceConfiguring QoS Attributes Creating a Class Map Creating a Policy Map78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling Verifying the Configuration MWR1900-1#show running-configMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Show Commands for Monitoring the MWR Command PurposeShow interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Clear ppp mux Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp mux interface interfaceIp rtp header-compressionEnables RTP header compression Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp compression-connectionsIp rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Standalone Mode y-cableMode y-cable Standby use-interfaceCommand Modes Command History Ppp muxPpp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux frame integer no ppp mux framePpp mux pid Ppp mux pid integerPpp mux subframe length Ppp mux subframe length integer No ppp mux subframe lengthPpp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Invoked y-cable mode Global configurationFollowing example enables redundancy mode Redundancy1describes the significant fields shown in the display Show ip rtp header-compressionShow ip rtp header-compression type number detail Field DescriptionThat can exist on an interface Show ppp mux Interface interfacePpp mux Enables PPP multiplexing/demultiplexing 2describes the significant fields shown in the displayThis command has no attributes Show redundancyStand-alone configuration Invokes y-cable modeInvokes redundancy mode StandbyStandalone Syntax Description DefaultsCable configuration No standaloneStandby use-interface Standby use-interface interface health revertive backhaulStandby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing MIB support Mode y-cable IN-2Command ConfiguringIN-4