Cisco Systems 78-13983-04 manual Standalone, Syntax Description Defaults, No standalone

Page 73

Chapter 5 Command Reference

standalone

standalone

Syntax Description

Defaults

To specify that the MWR 1900 is being used in a stand-alone configuration (which impacts the relays on the VWIC), use the standalone command. To use the MWR 1900 in a redundant configuration, use the no form of this command.

[no] standalone

This command has no attributes.

By default, the MWR 1900 is configured to be used in a redundant configuration (no standalone) and the relays are open.

Command Modes

Command History

Y-cable configuration

ReleaseModification

12.2(8)MC2	This command was introduced.

Usage Guidelines		Issuing the standalone command closes the relays on the VWICs installed in the MWR 1900.

Examples		The following example closes the relays so that the MWR 1900 can be used as a stand-alone device.
		standalone

Related Commands		Command	Description

		mode y-cable	Invokes y-cable mode.

		standby use-interface	Specifies the interfaces to be used for health and revertive interfaces.

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	78-13983-04	5-21

Image 73

Contents Customer Order Number DOC-7813983= Text Part Number Corporate HeadquartersCopyright 2002 Cisco Systems, Inc All rights reserved Limitations and Restrictions First-Time Configuration Software FeaturesAbout This Guide AudienceSaving Configuration Changes Using the Setup Command FacilityConfiguring PIM Configuring PPP MultiplexingWhere to Go Next Configuring RedundancyMode y-cable Assigning a QoS Boilerplate to an InterfacePage Audience ObjectivesOrganization Chapter Title DescriptionConvention Description Document ConventionsBoldface font Boldface screenRelated Documentation Additional InformationObtaining Documentation World Wide WebDocumentation CD-ROM Obtaining Technical AssistanceOrdering Documentation Documentation FeedbackCisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Benefits Overview of the MWRCisco IOS Software Software FeaturesNetwork Processor Software MLP, PPP Control Path IPCP, NCP, LCP, ClnsRTP/UDP Header Compression PPP Multiplexing/DemultiplexingRTP Header Compression Redundancy SupportMWR 1900 supports the following MIBs MIB SupportRFC1213-MIB RFC1253-MIB802.1Q VLANs Frame Relay FR Limitations and RestrictionsBefore You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Enter a host name for the router this example uses Viewing the configurationYou are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed First-Time Configuration Where to Go Next Where to Go NextGetting Help Cisco IOS Software BasicsConfigure terminal Understanding Command ModesExit , or logout As interface serial 0/0Saving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Enter global configuration mode Configuring the Host Name and PasswordPrompt changes to Routerconfig# Verifying the Version of Cisco IOS SoftwareExit to global configuration mode Configuring Loopback InterfacesExit interface configuration mode Change the name of the router to a meaningful nameConfiguring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation Configuring RTP/UDP Compression Configuring PPP MultiplexingTo set the default PPP protocol ID, enter To set the maximum length of the subframe, enterRPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 InterfacesSet the carrier delay for the serial interface Configuring E1 InterfacesConfiguring QoS Attributes Creating a Policy Map Creating a Class Map78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling MWR1900-1#show running-config Verifying the ConfigurationMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWRShow interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Related Commands Description Command Modes Command History Usage Guidelines ExamplesClear ppp mux Clear ppp mux interface interfaceConnections Interface configuration Syntax Description Defaults Command ModesIp rtp header-compressionEnables RTP header compression Ip rtp compression-connectionsIp rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Mode y-cable Mode y-cableStandalone Standby use-interfacePpp mux Command Modes Command HistoryPpp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Default maximum length is Interface configuration Defaults Command Modes Command HistoryPpp mux frame Ppp mux frame integer no ppp mux framePpp mux pid integer Ppp mux pidPpp mux subframe length integer No ppp mux subframe length Ppp mux subframe lengthPpp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Following example enables redundancy mode Global configurationInvoked y-cable mode RedundancyShow ip rtp header-compression type number detail Show ip rtp header-compression1describes the significant fields shown in the display Field DescriptionThat can exist on an interface Interface interface Show ppp mux2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexingShow redundancy This command has no attributesInvokes redundancy mode Invokes y-cable modeStand-alone configuration StandbyCable configuration Syntax Description DefaultsStandalone No standaloneStandby use-interface interface health revertive backhaul Standby use-interfaceStandby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing IN-2 MIB support Mode y-cableConfiguring CommandIN-4