Page 53
C H A P T E R 5
Command Reference
This chapter contains information about commands that were introduced specifically in support of the MWR 1900:
The following commands have been added or changed with this release:
•clear ppp mux
•mode y-cable
•ppp mux
•ppp mux delay
•ppp mux frame
•ppp mux pid
•ppp mux subframe length
•ppp mux subframe count
•redundancy
•show ppp mux
•show redundancy
•standalone
•standby use-interface
The following commands were not altered but have been included for your convenience:
•clear ip rtp header-compression
•ip rtp compression-connections
•ip rtp header-compression
•show ip rtp header-compression
Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide
Contents
Customer Order Number DOC-7813983= Text Part Number
Corporate Headquarters
Copyright 2002 Cisco Systems, Inc All rights reserved
Limitations and Restrictions First-Time Configuration
Software Features
About This Guide
Audience
Saving Configuration Changes
Using the Setup Command Facility
Configuring PIM
Configuring PPP Multiplexing
Where to Go Next
Configuring Redundancy
Mode y-cable
Assigning a QoS Boilerplate to an Interface
Page
Audience
Objectives
Organization
Chapter Title Description
Convention Description
Document Conventions
Boldface font
Boldface screen
Related Documentation
Additional Information
Obtaining Documentation
World Wide Web
Documentation CD-ROM
Obtaining Technical Assistance
Ordering Documentation
Documentation Feedback
Technical Assistance Center
To access Cisco.com, go to the following website
Cisco.com
Contacting TAC by Telephone
Benefits
Overview of the MWR
Cisco IOS Software
Software Features
Network Processor Software
MLP, PPP Control Path IPCP, NCP, LCP, Clns
RTP/UDP Header Compression
PPP Multiplexing/Demultiplexing
RTP Header Compression
Redundancy Support
MWR 1900 supports the following MIBs
MIB Support
RFC1213-MIB
RFC1253-MIB
802.1Q VLANs Frame Relay FR
Limitations and Restrictions
Understanding Interface Numbering
Understanding Boot Images
Before You Begin
Interface type Slot number/Interface number
Before Starting Your Router
Using the Setup Command Facility
Configuring Global Parameters
Enter a host name for the router this example uses
Viewing the configuration
Summary of interfaces is displayed
Completing the Configuration
You are then prompted to configure the specified interface
First-Time Configuration Where to Go Next
Where to Go Next
Getting Help
Cisco IOS Software Basics
Configure terminal
Understanding Command Modes
Exit , or logout
As interface serial 0/0
Saving Configuration Changes
Undoing a Command or Feature
Page
Configuring with the Command-Line Interface
Enter global configuration mode
Configuring the Host Name and Password
Prompt changes to Routerconfig#
Verifying the Version of Cisco IOS Software
Exit to global configuration mode
Configuring Loopback Interfaces
Exit interface configuration mode
Change the name of the router to a meaningful name
Setting the Speed and Duplex Mode
Configuring Fast Ethernet Interfaces
Configuring the FE Interface IP Address
Specify the speed
Configuring Routing Protocol Attributes
Configuring PIM
Configuring Hsrp Support
Specify a priority
Configuring Multilink Interfaces
Enabling the FE Interface
Enable multilink PPP operation
Configuring Multilink PPP
Configuring IP Address Assignment
Configuring RTP/UDP Compression
Configuring PPP Multiplexing
To set the default PPP protocol ID, enter
To set the maximum length of the subframe, enter
RPM-3config-if#ip rtp header-compression
Configuring T1 Interfaces
Configuring T1 and E1 Interfaces
Set the carrier delay for the serial interface
Configuring E1 Interfaces
Configuring QoS Attributes
Creating a Policy Map
Creating a Class Map
78-13983-04
Redundant MWR 1900s
Configuring Redundancy
Assigning a QoS Boilerplate to an Interface
Specify the interface to be used for backhauling
Exit y-mode configuration mode
Stand-Alone MWR
MWR1900-1#show running-config
Verifying the Configuration
Match access-group
Ip ospf message-digest-key 1 md5 mymd5pw
Ip ospf Hello-interval Ospf Dead-interval
Monitoring and Managing the MWR
Command Purpose
Show Commands for Monitoring the MWR
Show protocols
Show controllers
Show interface type slot / port
Command Reference
Clear ip rtp header-compression
Related Commands Description
Command Modes Command History Usage Guidelines Examples
Clear ppp mux
Clear ppp mux interface interface
Connections Interface configuration
Syntax Description Defaults Command Modes
Ip rtp header-compressionEnables RTP header compression
Ip rtp compression-connections
Passive
Syntax Description Defaults Command Modes Command History
Ip rtp header-compression
Related Commands Description
Mode y-cable
Mode y-cable
Standalone
Standby use-interface
Ppp mux
Command Modes Command History
Usage Guidelines Examples Related Commands
Ppp mux delay
Ppp mux delay integer no ppp mux delay
Default maximum length is Interface configuration
Defaults Command Modes Command History
Ppp mux frame
Ppp mux frame integer no ppp mux frame
Ppp mux pid integer
Ppp mux pid
Ppp mux subframe length integer No ppp mux subframe length
Ppp mux subframe length
Ppp mux subframe count integer No ppp mux subframe count
Default maximum is Interface configuration
Ppp mux subframe count
Following example enables redundancy mode
Global configuration
Invoked y-cable mode
Redundancy
Show ip rtp header-compression type number detail
Show ip rtp header-compression
1describes the significant fields shown in the display
Field Description
That can exist on an interface
Interface interface
Show ppp mux
2describes the significant fields shown in the display
Ppp mux Enables PPP multiplexing/demultiplexing
Show redundancy
This command has no attributes
Invokes redundancy mode
Invokes y-cable mode
Stand-alone configuration
Standby
Cable configuration
Syntax Description Defaults
Standalone
No standalone
Standby use-interface interface health revertive backhaul
Standby use-interface
Standby use-interface loopback102 revertive
Page
Counters, PPP multiplexing
Cisco IOS About Command modes Enable mode
IP address
IN-2
MIB support Mode y-cable
Configuring
Command
IN-4
