Cisco Systems 78-13983-04 manual Standby use-interface loopback102 revertive

Page 75

Chapter 5 Command Reference

standby use-interface

Examples		The following example specifies loopback101 as the health interface and loopback102 as the revertive
		interface.
		standby use-interface loopback101 health
		standby use-interface loopback102 revertive
		standby use-interface multilink1 backhaul

Related Commands		Command	Description

		mode y-cable	Invokes y-cable mode.

		redundancy	Invokes redundancy mode.

		standalone	Specifies whether the MWR 1900 router is used in a redundant or
			stand-alone configuration.

		standby	Sets HSRP attributes

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	78-13983-04	5-23

Image 75

Contents Customer Order Number DOC-7813983= Text Part Number Corporate HeadquartersCopyright 2002 Cisco Systems, Inc All rights reserved Audience Software FeaturesLimitations and Restrictions First-Time Configuration About This GuideConfiguring PPP Multiplexing Using the Setup Command FacilitySaving Configuration Changes Configuring PIMAssigning a QoS Boilerplate to an Interface Configuring RedundancyWhere to Go Next Mode y-cablePage Chapter Title Description ObjectivesAudience OrganizationBoldface screen Document ConventionsConvention Description Boldface fontWorld Wide Web Additional InformationRelated Documentation Obtaining DocumentationDocumentation Feedback Obtaining Technical AssistanceDocumentation CD-ROM Ordering DocumentationTo access Cisco.com, go to the following website Cisco.comTechnical Assistance Center Contacting TAC by Telephone Benefits Overview of the MWRMLP, PPP Control Path IPCP, NCP, LCP, Clns Software FeaturesCisco IOS Software Network Processor SoftwareRTP/UDP Header Compression PPP Multiplexing/DemultiplexingRTP Header Compression Redundancy SupportRFC1253-MIB MIB SupportMWR 1900 supports the following MIBs RFC1213-MIB802.1Q VLANs Frame Relay FR Limitations and RestrictionsUnderstanding Boot Images Before You BeginUnderstanding Interface Numbering Interface type Slot number/Interface number Using the Setup Command Facility Configuring Global ParametersBefore Starting Your Router Enter a host name for the router this example uses Viewing the configurationCompleting the Configuration You are then prompted to configure the specified interfaceSummary of interfaces is displayed First-Time Configuration Where to Go Next Where to Go NextGetting Help Cisco IOS Software BasicsAs interface serial 0/0 Understanding Command ModesConfigure terminal Exit , or logoutSaving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Verifying the Version of Cisco IOS Software Configuring the Host Name and PasswordEnter global configuration mode Prompt changes to Routerconfig#Change the name of the router to a meaningful name Configuring Loopback InterfacesExit to global configuration mode Exit interface configuration modeConfiguring Fast Ethernet Interfaces Configuring the FE Interface IP AddressSetting the Speed and Duplex Mode Configuring Routing Protocol Attributes Configuring PIMSpecify the speed Configuring Hsrp Support Configuring Multilink Interfaces Enabling the FE InterfaceSpecify a priority Configuring Multilink PPP Configuring IP Address AssignmentEnable multilink PPP operation To set the maximum length of the subframe, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the default PPP protocol ID, enterRPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 InterfacesSet the carrier delay for the serial interface Configuring E1 InterfacesConfiguring QoS Attributes Creating a Policy Map Creating a Class Map78-13983-04 Configuring Redundancy Assigning a QoS Boilerplate to an InterfaceRedundant MWR 1900s Exit y-mode configuration mode Stand-Alone MWRSpecify the interface to be used for backhauling MWR1900-1#show running-config Verifying the ConfigurationMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWRShow controllers Show interface type slot / portShow protocols Command Reference Clear ip rtp header-compression Clear ppp mux interface interface Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp muxIp rtp compression-connections Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp header-compressionEnables RTP header compressionSyntax Description Defaults Command Modes Command History Ip rtp header-compressionPassive Related Commands Description Standby use-interface Mode y-cableMode y-cable StandalonePpp mux Command Modes Command HistoryPpp mux delay Ppp mux delay integer no ppp mux delayUsage Guidelines Examples Related Commands Ppp mux frame integer no ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux framePpp mux pid integer Ppp mux pidPpp mux subframe length integer No ppp mux subframe length Ppp mux subframe lengthDefault maximum is Interface configuration Ppp mux subframe countPpp mux subframe count integer No ppp mux subframe count Redundancy Global configurationFollowing example enables redundancy mode Invoked y-cable modeField Description Show ip rtp header-compressionShow ip rtp header-compression type number detail 1describes the significant fields shown in the displayThat can exist on an interface Interface interface Show ppp mux2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexingShow redundancy This command has no attributesStandby Invokes y-cable modeInvokes redundancy mode Stand-alone configurationNo standalone Syntax Description DefaultsCable configuration StandaloneStandby use-interface interface health revertive backhaul Standby use-interfaceStandby use-interface loopback102 revertive Page Cisco IOS About Command modes Enable mode IP addressCounters, PPP multiplexing IN-2 MIB support Mode y-cableConfiguring CommandIN-4