Cisco Systems 78-13983-04 manual Mode y-cable, Standalone, Standby use-interface, Redundancy

Page 59

Chapter 5 Command Reference

mode y-cable

mode y-cable

To access the command mode that allows you to manually control the relays on the VWIC card, use the mode y-cablecommand.

		mode y-cable

Syntax Description		This command has no parameters, it invokes the y-cable mode.

Defaults		There are no default settings or behaviors.

Command Modes		Redundancy configuration

Command History		Release	Modification

		12.2(8)MC2	This command was introduced.


Examples		The following example enables y-cable mode.
		mode y-cable

Related Commands		Command	Description

		standalone	Indicates whether the MWR 1900 router is being used as a standalone
			device and manually sets the relays.

		standby use-interface	Designates a loopback interface as a health or revertive interface.

		redundancy	Invoked redundancy mode.

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

	78-13983-04	5-7

Image 59

Contents Customer Order Number DOC-7813983= Text Part Number Corporate HeadquartersCopyright 2002 Cisco Systems, Inc All rights reserved Audience Software FeaturesLimitations and Restrictions First-Time Configuration About This GuideConfiguring PPP Multiplexing Using the Setup Command FacilitySaving Configuration Changes Configuring PIMAssigning a QoS Boilerplate to an Interface Configuring RedundancyWhere to Go Next Mode y-cablePage Chapter Title Description ObjectivesAudience OrganizationBoldface screen Document ConventionsConvention Description Boldface fontWorld Wide Web Additional InformationRelated Documentation Obtaining DocumentationDocumentation Feedback Obtaining Technical AssistanceDocumentation CD-ROM Ordering DocumentationTechnical Assistance Center To access Cisco.com, go to the following websiteCisco.com Contacting TAC by Telephone Benefits Overview of the MWRMLP, PPP Control Path IPCP, NCP, LCP, Clns Software FeaturesCisco IOS Software Network Processor SoftwareRTP/UDP Header Compression PPP Multiplexing/DemultiplexingRTP Header Compression Redundancy SupportRFC1253-MIB MIB SupportMWR 1900 supports the following MIBs RFC1213-MIB802.1Q VLANs Frame Relay FR Limitations and RestrictionsUnderstanding Interface Numbering Understanding Boot ImagesBefore You Begin Interface type Slot number/Interface number Before Starting Your Router Using the Setup Command FacilityConfiguring Global Parameters Enter a host name for the router this example uses Viewing the configurationSummary of interfaces is displayed Completing the ConfigurationYou are then prompted to configure the specified interface First-Time Configuration Where to Go Next Where to Go NextGetting Help Cisco IOS Software BasicsAs interface serial 0/0 Understanding Command ModesConfigure terminal Exit , or logoutSaving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Verifying the Version of Cisco IOS Software Configuring the Host Name and PasswordEnter global configuration mode Prompt changes to Routerconfig#Change the name of the router to a meaningful name Configuring Loopback InterfacesExit to global configuration mode Exit interface configuration modeSetting the Speed and Duplex Mode Configuring Fast Ethernet InterfacesConfiguring the FE Interface IP Address Specify the speed Configuring Routing Protocol AttributesConfiguring PIM Configuring Hsrp Support Specify a priority Configuring Multilink InterfacesEnabling the FE Interface Enable multilink PPP operation Configuring Multilink PPPConfiguring IP Address Assignment To set the maximum length of the subframe, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the default PPP protocol ID, enterRPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 InterfacesSet the carrier delay for the serial interface Configuring E1 InterfacesConfiguring QoS Attributes Creating a Policy Map Creating a Class Map78-13983-04 Redundant MWR 1900s Configuring RedundancyAssigning a QoS Boilerplate to an Interface Specify the interface to be used for backhauling Exit y-mode configuration modeStand-Alone MWR MWR1900-1#show running-config Verifying the ConfigurationMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWRShow protocols Show controllersShow interface type slot / port Command Reference Clear ip rtp header-compression Clear ppp mux interface interface Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp muxIp rtp compression-connections Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp header-compressionEnables RTP header compressionPassive Syntax Description Defaults Command Modes Command HistoryIp rtp header-compression Related Commands Description Standby use-interface Mode y-cableMode y-cable StandalonePpp mux Command Modes Command HistoryUsage Guidelines Examples Related Commands Ppp mux delayPpp mux delay integer no ppp mux delay Ppp mux frame integer no ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux framePpp mux pid integer Ppp mux pidPpp mux subframe length integer No ppp mux subframe length Ppp mux subframe lengthPpp mux subframe count integer No ppp mux subframe count Default maximum is Interface configurationPpp mux subframe count Redundancy Global configurationFollowing example enables redundancy mode Invoked y-cable modeField Description Show ip rtp header-compressionShow ip rtp header-compression type number detail 1describes the significant fields shown in the displayThat can exist on an interface Interface interface Show ppp mux2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexingShow redundancy This command has no attributesStandby Invokes y-cable modeInvokes redundancy mode Stand-alone configurationNo standalone Syntax Description DefaultsCable configuration StandaloneStandby use-interface interface health revertive backhaul Standby use-interfaceStandby use-interface loopback102 revertive Page Counters, PPP multiplexing Cisco IOS About Command modes Enable modeIP address IN-2 MIB support Mode y-cableConfiguring CommandIN-4