Cisco Systems 78-13983-04 manual Cisco IOS Software Basics, Getting Help

Page 25

C H A P T E R 3

Cisco IOS Software Basics

This chapter describes what you need to know about the Cisco IOS software before you configure the router using the command-line interface (CLI). This chapter includes the following:

Getting Help, page 3-1

Understanding Command Modes, page 3-2

Undoing a Command or Feature, page 3-3

Saving Configuration Changes, page 3-3

Where to Go Next, page 3-3

Understanding these concepts will save time as you begin to use the CLI. If you have never used the Cisco IOS software or need a refresher, take a few minutes to read this chapter before you proceed to the next chapter.

If you are already familiar with the Cisco IOS software, proceed to Chapter 4, “Configuring with the Command-Line Interface.”

Getting Help

Use the question mark (?) and arrow keys to help you enter commands:

For a list of available commands, enter a question mark:

Router> ?

To complete a command, enter a few known characters followed by a question mark (with no space):

Router> s?

For a list of command variables, enter the command followed by a space and a question mark:

Router> show ?

To redisplay a command you previously entered, press the up arrow key. You can continue to press the up arrow key for more commands.

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

 

78-13983-04

3-1

 

 

 

Image 25
Contents Customer Order Number DOC-7813983= Text Part Number Corporate HeadquartersCopyright 2002 Cisco Systems, Inc All rights reserved Limitations and Restrictions First-Time Configuration Software FeaturesAbout This Guide AudienceSaving Configuration Changes Using the Setup Command FacilityConfiguring PIM Configuring PPP MultiplexingWhere to Go Next Configuring RedundancyMode y-cable Assigning a QoS Boilerplate to an InterfacePage Audience ObjectivesOrganization Chapter Title DescriptionConvention Description Document ConventionsBoldface font Boldface screenRelated Documentation Additional InformationObtaining Documentation World Wide WebDocumentation CD-ROM Obtaining Technical AssistanceOrdering Documentation Documentation FeedbackCisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Benefits Overview of the MWRCisco IOS Software Software FeaturesNetwork Processor Software MLP, PPP Control Path IPCP, NCP, LCP, ClnsRTP/UDP Header Compression PPP Multiplexing/DemultiplexingRTP Header Compression Redundancy SupportMWR 1900 supports the following MIBs MIB SupportRFC1213-MIB RFC1253-MIB802.1Q VLANs Frame Relay FR Limitations and RestrictionsBefore You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Enter a host name for the router this example uses Viewing the configurationYou are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed First-Time Configuration Where to Go Next Where to Go NextGetting Help Cisco IOS Software BasicsConfigure terminal Understanding Command ModesExit , or logout As interface serial 0/0Saving Configuration Changes Undoing a Command or FeaturePage Configuring with the Command-Line Interface Enter global configuration mode Configuring the Host Name and PasswordPrompt changes to Routerconfig# Verifying the Version of Cisco IOS SoftwareExit to global configuration mode Configuring Loopback InterfacesExit interface configuration mode Change the name of the router to a meaningful nameConfiguring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation Configuring RTP/UDP Compression Configuring PPP MultiplexingTo set the default PPP protocol ID, enter To set the maximum length of the subframe, enterRPM-3config-if#ip rtp header-compression Configuring T1 Interfaces Configuring T1 and E1 InterfacesSet the carrier delay for the serial interface Configuring E1 InterfacesConfiguring QoS Attributes Creating a Policy Map Creating a Class Map78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling MWR1900-1#show running-config Verifying the ConfigurationMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Command Purpose Show Commands for Monitoring the MWRShow interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Related Commands Description Command Modes Command History Usage Guidelines ExamplesClear ppp mux Clear ppp mux interface interfaceConnections Interface configuration Syntax Description Defaults Command ModesIp rtp header-compressionEnables RTP header compression Ip rtp compression-connectionsIp rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Mode y-cable Mode y-cableStandalone Standby use-interfacePpp mux Command Modes Command HistoryPpp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Default maximum length is Interface configuration Defaults Command Modes Command HistoryPpp mux frame Ppp mux frame integer no ppp mux framePpp mux pid integer Ppp mux pidPpp mux subframe length integer No ppp mux subframe length Ppp mux subframe lengthPpp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Following example enables redundancy mode Global configurationInvoked y-cable mode RedundancyShow ip rtp header-compression type number detail Show ip rtp header-compression1describes the significant fields shown in the display Field DescriptionThat can exist on an interface Interface interface Show ppp mux2describes the significant fields shown in the display Ppp mux Enables PPP multiplexing/demultiplexingShow redundancy This command has no attributesInvokes redundancy mode Invokes y-cable modeStand-alone configuration StandbyCable configuration Syntax Description DefaultsStandalone No standaloneStandby use-interface interface health revertive backhaul Standby use-interfaceStandby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing IN-2 MIB support Mode y-cableConfiguring CommandIN-4