Cisco Systems 78-13983-04 manual Verifying the Configuration, MWR1900-1#show running-config

Page 46

Chapter 4 Configuring with the Command-Line Interface

Saving Configuration Changes

Saving Configuration Changes

To prevent the loss of the router configuration, save it to non-volatile random access memory (NVRAM). To save the configuration to NVRAM, do the following:

Step 1 Exit configuration mode.

Router(config)# exit

Note You can press Ctrl-zin any mode to immediately return to enable mode (Router#), instead of entering exit, which returns you to the previous mode.

Step 2 Save the configuration changes to NVRAM so that they are not lost during resets, power cycles, or power outages.

Router# copy running-config startup-config

Verifying the Configuration

To verify the configuration of the MWR 1900, enter the following command:

MWR1900-1#show running-config

hostname MWR1900-1

!

boot system slot0:mwr-1900-boot

!

!description Loopback IP for O & M

interface loopback 0

ip address 10.1.170.3 255.255.255.255

!description Loopback IP for IP Unnumbered

interface loopback 2

ip address 192.168.170.2 255.255.255.255

interface loopback101

description Health Loopback Interface no ip address

interface loopback102

description Revertive Loopback Interface no ip address

enable password cisco

memory-size iomem 25

disable-eadi

redundancy mode y-cable

standby use-interface Loopback101 health

Cisco MWR 1900 Mobile Wireless Edge Router Software Configuration Guide

4-18

78-13983-04

 

 

Image 46
Contents Corporate Headquarters Customer Order Number DOC-7813983= Text Part NumberCopyright 2002 Cisco Systems, Inc All rights reserved About This Guide Software FeaturesLimitations and Restrictions First-Time Configuration AudienceConfiguring PIM Using the Setup Command FacilitySaving Configuration Changes Configuring PPP MultiplexingMode y-cable Configuring RedundancyWhere to Go Next Assigning a QoS Boilerplate to an InterfacePage Organization ObjectivesAudience Chapter Title DescriptionBoldface font Document ConventionsConvention Description Boldface screenObtaining Documentation Additional InformationRelated Documentation World Wide WebOrdering Documentation Obtaining Technical AssistanceDocumentation CD-ROM Documentation FeedbackCisco.com To access Cisco.com, go to the following websiteTechnical Assistance Center Contacting TAC by Telephone Overview of the MWR BenefitsNetwork Processor Software Software FeaturesCisco IOS Software MLP, PPP Control Path IPCP, NCP, LCP, ClnsPPP Multiplexing/Demultiplexing RTP/UDP Header CompressionRedundancy Support RTP Header CompressionRFC1213-MIB MIB SupportMWR 1900 supports the following MIBs RFC1253-MIBLimitations and Restrictions 802.1Q VLANs Frame Relay FRBefore You Begin Understanding Boot ImagesUnderstanding Interface Numbering Interface type Slot number/Interface number Configuring Global Parameters Using the Setup Command FacilityBefore Starting Your Router Viewing the configuration Enter a host name for the router this example usesYou are then prompted to configure the specified interface Completing the ConfigurationSummary of interfaces is displayed Where to Go Next First-Time Configuration Where to Go NextCisco IOS Software Basics Getting HelpExit , or logout Understanding Command ModesConfigure terminal As interface serial 0/0Undoing a Command or Feature Saving Configuration ChangesPage Configuring with the Command-Line Interface Prompt changes to Routerconfig# Configuring the Host Name and PasswordEnter global configuration mode Verifying the Version of Cisco IOS SoftwareExit interface configuration mode Configuring Loopback InterfacesExit to global configuration mode Change the name of the router to a meaningful nameConfiguring the FE Interface IP Address Configuring Fast Ethernet InterfacesSetting the Speed and Duplex Mode Configuring PIM Configuring Routing Protocol AttributesSpecify the speed Configuring Hsrp Support Enabling the FE Interface Configuring Multilink InterfacesSpecify a priority Configuring IP Address Assignment Configuring Multilink PPPEnable multilink PPP operation To set the default PPP protocol ID, enter Configuring PPP MultiplexingConfiguring RTP/UDP Compression To set the maximum length of the subframe, enterRPM-3config-if#ip rtp header-compression Configuring T1 and E1 Interfaces Configuring T1 InterfacesConfiguring E1 Interfaces Set the carrier delay for the serial interfaceConfiguring QoS Attributes Creating a Class Map Creating a Policy Map78-13983-04 Assigning a QoS Boilerplate to an Interface Configuring RedundancyRedundant MWR 1900s Stand-Alone MWR Exit y-mode configuration modeSpecify the interface to be used for backhauling Verifying the Configuration MWR1900-1#show running-configMatch access-group Ip ospf message-digest-key 1 md5 mymd5pw Ip ospf Hello-interval Ospf Dead-interval Monitoring and Managing the MWR Show Commands for Monitoring the MWR Command PurposeShow interface type slot / port Show controllersShow protocols Command Reference Clear ip rtp header-compression Clear ppp mux Command Modes Command History Usage Guidelines ExamplesRelated Commands Description Clear ppp mux interface interfaceIp rtp header-compressionEnables RTP header compression Syntax Description Defaults Command ModesConnections Interface configuration Ip rtp compression-connectionsIp rtp header-compression Syntax Description Defaults Command Modes Command HistoryPassive Related Commands Description Standalone Mode y-cableMode y-cable Standby use-interfaceCommand Modes Command History Ppp muxPpp mux delay integer no ppp mux delay Ppp mux delayUsage Guidelines Examples Related Commands Ppp mux frame Defaults Command Modes Command HistoryDefault maximum length is Interface configuration Ppp mux frame integer no ppp mux framePpp mux pid Ppp mux pid integerPpp mux subframe length Ppp mux subframe length integer No ppp mux subframe lengthPpp mux subframe count Default maximum is Interface configurationPpp mux subframe count integer No ppp mux subframe count Invoked y-cable mode Global configurationFollowing example enables redundancy mode Redundancy1describes the significant fields shown in the display Show ip rtp header-compressionShow ip rtp header-compression type number detail Field DescriptionThat can exist on an interface Show ppp mux Interface interfacePpp mux Enables PPP multiplexing/demultiplexing 2describes the significant fields shown in the displayThis command has no attributes Show redundancyStand-alone configuration Invokes y-cable modeInvokes redundancy mode StandbyStandalone Syntax Description DefaultsCable configuration No standaloneStandby use-interface Standby use-interface interface health revertive backhaulStandby use-interface loopback102 revertive Page IP address Cisco IOS About Command modes Enable modeCounters, PPP multiplexing MIB support Mode y-cable IN-2Command ConfiguringIN-4