Cisco Systems AS5350XM, AS5400XM manual Online Insertion and Removal of the CT3 Feature Card

Page 46

Chapter 4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

To remove a feature card without dropping any calls or connections, you will need to take the feature card out of service by using the busyout command to disable the feature card. The busyout command is executed on a per–feature card basis and will disable the card after waiting for the active services to terminate.

If there are active calls on the feature card after you execute the busyout command, wait for the calls to drop. To view the status of the termination process, use the show busyout command.

Caution The online installation and removal (OIR) of new cards should be done only during times of low CPU utilization, such as during maintenance.

Caution To avoid erroneous failure messages, remove or insert only one feature card at a time.

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically.

If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide.

Removing the CT3 Feature Card

To remove the CT3 feature card, follow these steps.

Note The OIR procedure for the CT3 feature card is similar to that for the T1 or E1 feature card. See the “Online Insertion and Removal Example for the T1 or E1 Feature Card” section on page 3-6for an example of the output during OIR of an E1 feature card.

Step 1 Determine which slot the feature card is in (see Figure 4-2and Figure 4-3) by entering the show chassis slot command in privileged EXEC mode:

Router# show chassis slot

Note These commands are not valid for slot 0. Slot 0 is the motherboard.

Figure 4-2 Slot Numbering on the Cisco AS5350XM Chassis

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Slot 0

 

 

 

 

Slot 2

Slot 1

Slot 3

 

 

 

 

 

 

 

 

36006

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

4-2

78-17406-01

 

 

Image 46
Contents Corporate Headquarters Customer Order Number DOC-7817406= Text Part NumberPage N T E N T S T1 and E1 Feature Cards Installing PVDM2 Modules in the Voice Feature Card Page Document Organization Chapter Title DescriptionDocument Conventions Convention DescriptionBewaar Deze Instructies Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança78-17406-01 GEM Disse Anvisninger Xiii Cisco.com Obtaining DocumentationDocumentation Feedback Product Documentation DVDReporting Security Problems in Cisco Products Cisco Product Security OverviewObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information XviiiXix Page Safety Warnings, Recommendations, and Tools Required General SafetyMaintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and EquipmentWhere to Go Next Cisco AS5350XM Chassis Feature CardsOverview Cisco AS5400XM ChassisOnline Insertion and Removal of Feature Cards Removing and Installing Populated Carrier CardsRemoving a Populated Carrier Card Loosening the Captive Screws on the Cisco AS5350XM Installing a Populated Carrier Card Removing the Carrier Card from the Cisco AS5400XMInstalling the Carrier Card in the Cisco AS5400XM 11 Blank Feature Card Cover Getting HelpPage T1 and E1 Feature Cards Description Specification 8-Port T1 or E1 Feature CardRemoving the T1 or E1 Feature Card Router# show chassis slotSlot Numbering on the Cisco AS5400XM Chassis 36814 10 Blank Feature Card Cover Router# clear port 1/70 Router# show chassis slot Installing the T1 or E1 Feature Card 36817 Configuration Configuring Input Impedance for the E1 Feature CardCommand Purpose Router# show running-config VerificationChannelized T3 Feature Card Online Insertion and Removal of the CT3 Feature Card Removing the CT3 Feature CardSlot 6Slot Screw Carrier Card Installing the CT3 Feature Card Blank Feature Card Cover58762 Channelized T3 Feature Card Getting Help Page Universal Port and Dial-Only Feature Cards Feature Cards Installed Services Supported Universal Port or Dial-Only Feature CardRemoving the Universal Port or Dial-Only Feature Card Statement 36821 Show busyout Router# clear port Installing the Universal Port or Dial-Only Feature Card Their holes System Processing Engine Firmware Voice Feature Card Codec Type Per AS5X-PVDM2-64 Per Voice Feature CardRestrictions for the Voice Feature Card Feature Cards Present at Power On Feature Cards SupportedOnline Insertion and Removal of the Voice Feature Card Removing the Voice Feature CardStatement DFC DFC Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Orienting the PVDM2 Module During Installation Removing PVDM2 Modules From the Voice Feature CardInstalling PVDM2 Modules in the Voice Feature Card Digital Signal Processor Firmware View from front of boardPage Troubleshooting LEDs8-Port T1 or E1 Feature Card LEDs Feature Card State DescriptionLED Mixing WAN Feature Cards ActivityMixing Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment Displaying Environment Status Router# show environment Using Drop and Insert Mode on the CT3 Feature Card Command as followsTroubleshooting Network Interfaces Page Cabling Specifications RJ-45 Pin DescriptionRJ-45 Pin Signal Description Direction DB-15 Pin Cable Description Part Number Product NumberRJ-45 Pin Signal Description Direction BNC Pin RJ-45 Pin Signal DescriptionRJ-45 Pin Signal Description Direction Twinax Pin RJ-45 Pin Signal Description Direction RJ-45 TE Pin RJ-45 Pin Signal Description Direction RJ-45 NT PinRJ-45 Pin Signal Description Direction RJ-45 Pin Signal Description Direction BarePort T1 or E1 Feature Card Cable and Port Pinouts From Signal DirectionTxtip 35058 35059 35060 Figure A-10 Securing the Cable Bracket to the Rack CT3 Feature Card Cable and Port Pinouts Pin DescriptionBantam Jack Port Pinouts Tip RingAppendix a Cabling Specifications Bantam Jack Port Pinouts Numerics IN-2 IN-3 IN-4
Related manuals
Manual 68 pages 41.48 Kb Manual 98 pages 24.32 Kb Manual 6 pages 52.67 Kb