Cisco Systems AS5400XM, AS5350XM manual Installing the CT3 Feature Card, Blank Feature Card Cover

Page 49

Chapter 4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

Figure 4-6 Removing the Feature Card from the Cisco AS5350XM Universal Gateway

58761

Figure 4-7 Removing the Feature Card from the Cisco AS5400XM Universal Gateway

37168

Step 10 After you remove the feature card from the chassis, set it aside on an ESD-preventive mat.

Step 11 If a feature card slot on the carrier card is to remain empty, install a blank cover over the open feature card slot to ensure proper airflow inside the chassis. (See Figure 4-8.)

Figure 4-8 Blank Feature Card Cover

36033

Installing the CT3 Feature Card

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Note When you replace a feature card with a new feature card of the same type in the same slot, the system software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system.

For configuration details, see the Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

	78-17406-01	4-5

Image 49

Contents Customer Order Number DOC-7817406= Text Part Number Corporate HeadquartersPage N T E N T S T1 and E1 Feature Cards Installing PVDM2 Modules in the Voice Feature Card Page Chapter Title Description Document OrganizationConvention Description Document ConventionsWarnung Wichtige Sicherheitshinweise Bewaar Deze InstructiesAviso Instruções Importantes DE Segurança Avvertenza Importanti Istruzioni Sulla Sicurezza78-17406-01 GEM Disse Anvisninger Xiii Documentation Feedback Obtaining DocumentationCisco.com Product Documentation DVDCisco Product Security Overview Reporting Security Problems in Cisco ProductsCisco Technical Support & Documentation Website Obtaining Technical AssistanceDefinitions of Service Request Severity Submitting a Service RequestXviii Obtaining Additional Publications and InformationXix Page General Safety Safety Warnings, Recommendations, and Tools RequiredMaintaining Safety with Electricity Required Tools and Equipment Preventing Electrostatic DischargeWhere to Go Next Overview Feature CardsCisco AS5350XM Chassis Cisco AS5400XM ChassisRemoving and Installing Populated Carrier Cards Online Insertion and Removal of Feature CardsRemoving a Populated Carrier Card Loosening the Captive Screws on the Cisco AS5350XM Removing the Carrier Card from the Cisco AS5400XM Installing a Populated Carrier CardInstalling the Carrier Card in the Cisco AS5400XM Getting Help 11 Blank Feature Card CoverPage T1 and E1 Feature Cards 8-Port T1 or E1 Feature Card Description SpecificationRouter# show chassis slot Removing the T1 or E1 Feature CardSlot Numbering on the Cisco AS5400XM Chassis 36814 10 Blank Feature Card Cover Router# clear port 1/70 Router# show chassis slot Installing the T1 or E1 Feature Card 36817 Configuration Configuring Input Impedance for the E1 Feature CardCommand Purpose Verification Router# show running-configChannelized T3 Feature Card Removing the CT3 Feature Card Online Insertion and Removal of the CT3 Feature CardSlot 6Slot Screw Carrier Card Blank Feature Card Cover Installing the CT3 Feature Card58762 Channelized T3 Feature Card Getting Help Page Universal Port and Dial-Only Feature Cards Universal Port or Dial-Only Feature Card Feature Cards Installed Services SupportedRemoving the Universal Port or Dial-Only Feature Card Statement 36821 Show busyout Router# clear port Installing the Universal Port or Dial-Only Feature Card Their holes System Processing Engine Firmware Codec Type Per AS5X-PVDM2-64 Per Voice Feature Card Voice Feature CardFeature Cards Present at Power On Feature Cards Supported Restrictions for the Voice Feature CardRemoving the Voice Feature Card Online Insertion and Removal of the Voice Feature CardStatement DFC DFC Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Removing PVDM2 Modules From the Voice Feature Card Orienting the PVDM2 Module During InstallationInstalling PVDM2 Modules in the Voice Feature Card View from front of board Digital Signal Processor FirmwarePage LEDs Troubleshooting8-Port T1 or E1 Feature Card LEDs State Description Feature CardLED Activity Mixing WAN Feature CardsMixing Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment Displaying Environment Status Router# show environment Command as follows Using Drop and Insert Mode on the CT3 Feature CardTroubleshooting Network Interfaces Page RJ-45 Pin Description Cabling SpecificationsCable Description Part Number Product Number RJ-45 Pin Signal Description Direction DB-15 PinRJ-45 Pin Signal Description Direction BNC Pin RJ-45 Pin Signal DescriptionRJ-45 Pin Signal Description Direction Twinax Pin RJ-45 Pin Signal Description Direction RJ-45 NT Pin RJ-45 Pin Signal Description Direction RJ-45 TE PinRJ-45 Pin Signal Description Direction Bare RJ-45 Pin Signal Description DirectionFrom Signal Direction Port T1 or E1 Feature Card Cable and Port PinoutsTxtip 35058 35059 35060 Figure A-10 Securing the Cable Bracket to the Rack Pin Description CT3 Feature Card Cable and Port PinoutsTip Ring Bantam Jack Port PinoutsAppendix a Cabling Specifications Bantam Jack Port Pinouts Numerics IN-2 IN-3 IN-4

Related manuals

Manual 68 pages 41.48 Kb

Manual 98 pages 24.32 Kb

Manual 6 pages 52.67 Kb