Cisco Systems AS5350XM, AS5400XM manual Statement

Page 56

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Figure 5-2 Slot Numbering on the Cisco AS5350XM Chassis





			Slot 0
	Slot 2		Slot 0		Slot 1		Slot 3
					Slot 1		Slot 3

Figure 5-3 Slot Numbering on the Cisco AS5400XM Chassis






			Slot 0		Slot 1
		Slot	2			Slot	3
	Slot	4					Slot	5
Slot	6							Slot	7

36006

34977

Step 2 Initialize the software busyout procedure by entering the busyout command:

Router# busyout slot-number

Step 3 To check busyout status for the slot, enter the show busyout command:

Router# show busyout slot-number

Step 4 You can use the clear port command to immediately disable active calls on a universal port or dial-only feature card.

Router# clear port slot-number/port number

Step 5 Verify that the OK/MAINT LED is off; this indicates that the feature card is offline and ready to be removed.

Note The OK/MAINT LED is green before you enter the busyout command. After you enter the busyout command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources taken out of service, indicating that busyout is complete.

Step 6 Attach an ESD-preventive wrist strap.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Step 7 Loosen the two captive screws that secure the feature card to the chassis until each screw is free of the chassis. (See Figure 5-4and Figure 5-5.)

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-4	78-17406-01

Image 56

Contents Corporate Headquarters Customer Order Number DOC-7817406= Text Part NumberPage N T E N T S T1 and E1 Feature Cards Installing PVDM2 Modules in the Voice Feature Card Page Document Organization Chapter Title DescriptionDocument Conventions Convention DescriptionBewaar Deze Instructies Warnung Wichtige SicherheitshinweiseAvvertenza Importanti Istruzioni Sulla Sicurezza Aviso Instruções Importantes DE Segurança78-17406-01 GEM Disse Anvisninger Xiii Obtaining Documentation Documentation FeedbackCisco.com Product Documentation DVDReporting Security Problems in Cisco Products Cisco Product Security OverviewObtaining Technical Assistance Cisco Technical Support & Documentation WebsiteSubmitting a Service Request Definitions of Service Request SeverityObtaining Additional Publications and Information XviiiXix Page Safety Warnings, Recommendations, and Tools Required General SafetyMaintaining Safety with Electricity Preventing Electrostatic Discharge Required Tools and EquipmentWhere to Go Next Feature Cards OverviewCisco AS5350XM Chassis Cisco AS5400XM ChassisOnline Insertion and Removal of Feature Cards Removing and Installing Populated Carrier CardsRemoving a Populated Carrier Card Loosening the Captive Screws on the Cisco AS5350XM Installing a Populated Carrier Card Removing the Carrier Card from the Cisco AS5400XMInstalling the Carrier Card in the Cisco AS5400XM 11 Blank Feature Card Cover Getting HelpPage T1 and E1 Feature Cards Description Specification 8-Port T1 or E1 Feature CardRemoving the T1 or E1 Feature Card Router# show chassis slotSlot Numbering on the Cisco AS5400XM Chassis 36814 10 Blank Feature Card Cover Router# clear port 1/70 Router# show chassis slot Installing the T1 or E1 Feature Card 36817 Command Purpose Configuring Input Impedance for the E1 Feature CardConfiguration Router# show running-config VerificationChannelized T3 Feature Card Online Insertion and Removal of the CT3 Feature Card Removing the CT3 Feature CardSlot 6Slot Screw Carrier Card Installing the CT3 Feature Card Blank Feature Card Cover58762 Channelized T3 Feature Card Getting Help Page Universal Port and Dial-Only Feature Cards Feature Cards Installed Services Supported Universal Port or Dial-Only Feature CardRemoving the Universal Port or Dial-Only Feature Card Statement 36821 Show busyout Router# clear port Installing the Universal Port or Dial-Only Feature Card Their holes System Processing Engine Firmware Voice Feature Card Codec Type Per AS5X-PVDM2-64 Per Voice Feature CardRestrictions for the Voice Feature Card Feature Cards Present at Power On Feature Cards SupportedOnline Insertion and Removal of the Voice Feature Card Removing the Voice Feature CardStatement DFC DFC Installing the Voice Feature Card Replacing PVDM2 Modules in the Voice Feature Card Orienting the PVDM2 Module During Installation Removing PVDM2 Modules From the Voice Feature CardInstalling PVDM2 Modules in the Voice Feature Card Digital Signal Processor Firmware View from front of boardPage Troubleshooting LEDs8-Port T1 or E1 Feature Card LEDs Feature Card State DescriptionLED Mixing WAN Feature Cards ActivityMixing Universal Port and Dial-Only Feature Cards Monitoring the Chassis Environment Displaying Environment Status Router# show environment Using Drop and Insert Mode on the CT3 Feature Card Command as followsTroubleshooting Network Interfaces Page Cabling Specifications RJ-45 Pin DescriptionRJ-45 Pin Signal Description Direction DB-15 Pin Cable Description Part Number Product NumberRJ-45 Pin Signal Description Direction Twinax Pin RJ-45 Pin Signal DescriptionRJ-45 Pin Signal Description Direction BNC Pin RJ-45 Pin Signal Description Direction RJ-45 TE Pin RJ-45 Pin Signal Description Direction RJ-45 NT PinRJ-45 Pin Signal Description Direction RJ-45 Pin Signal Description Direction BarePort T1 or E1 Feature Card Cable and Port Pinouts From Signal DirectionTxtip 35058 35059 35060 Figure A-10 Securing the Cable Bracket to the Rack CT3 Feature Card Cable and Port Pinouts Pin DescriptionBantam Jack Port Pinouts Tip RingAppendix a Cabling Specifications Bantam Jack Port Pinouts Numerics IN-2 IN-3 IN-4

Related manuals

Manual 68 pages 41.48 Kb

Manual 98 pages 24.32 Kb

Manual 6 pages 52.67 Kb