Cisco Systems 2600 manual To the other side of the chassis. Brackets for 19-inch rack

Page 52

Chapter 3 Installing the Router

Setting Up the Chassis

Note The following illustrations show how to connect the bracket to one side of the chassis. The second bracket connects to the opposite side of the chassis.

Figure 3-5 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.5-Inch Opening)

62676

Note: The second bracket attaches to the other side of the chassis.

Note When installed in a 19-inch rack with a 17.75-inch opening, Cisco 2600 series routers protrude beyond the front of the rack.

Figure 3-6 Bracket Installation—Front Panel Forward (19-Inch Rack with a 17.75-Inch Opening or a 23- or 24-Inch Rack)

Note: The second bracket attaches

to the other side of the chassis. Brackets for 19-inch rack

Brackets for

23-inch or 24-inch rack

62881

Cisco 2600 Series Routers Hardware Installation Guide

3-6	OL-2171-06

Image 52

Contents Cisco 2600 Series Routers Hardware Installation Guide Corporate HeadquartersCisco 2600 Series Routers Hardware Installation Guide N T E N T S IiiSerial DTE or DCE Devices Initial Configuration Using the Setup Command Facility Procedure for the tftpdnld Command Configuration Register Objectives ViiAudience OrganizationConventions Chapter Title DescriptionSafety Warnings Bewaar Deze InstructiesWarnung Wichtige Sicherheitshinweise Avvertenza Importanti Istruzioni Sulla SicurezzaAviso Instruções Importantes DE Segurança Guarde Estas InstruçõesGEM Disse Anvisninger XiiXiii Related Documentation XivCisco Product Document Title Cisco 90-Day Limited Hardware Warranty Terms Duration of Hardware WarrantyReplacement, Repair, or Refund Policy for Hardware XviObtaining Documentation Documentation FeedbackCisco.com Ordering DocumentationSubmitting a Service Request Obtaining Technical AssistanceCisco Technical Support Website XviiiObtaining Additional Publications and Information Definitions of Service Request SeverityXix Preface Obtaining Additional Publications and Information Hardware Features Overview of Cisco 2600 Series RoutersAdvanced CiscoPower Reading the Front-Panel LEDsRPS ActivityPWR SYS/RPSReading the Rear-Panel LEDs ACTCisco 2613-Rear-Panel LEDs ACT LinkFDX Modules, Interface Cards, and Memory CF1Interface Numbering WAN and LAN Interface Numbering11 Interface Numbering in Chassis with 1-RU Height Description Specification System SpecificationsVoice Interface Numbering Regulatory Compliance Safety Recommendations Safety with ElectricityPreventing Electrostatic Discharge Damage Power Supply Considerations Power Source Input Power Tolerance LimitsGeneral Site Requirements Site EnvironmentSite Configuration Installation ChecklistEquipment Racks Creating a Site Log Task Verified by DateTools and Equipment for Installation and Maintenance Inspecting the RouterConsole and Auxiliary Port Considerations Console Port ConnectionsPreparing to Connect to a Network Auxiliary Port ConnectionsEthernet Connections Token Ring ConnectionsSerial Connections Configuring Serial ConnectionsSerial DTE or DCE Devices Distance Limitations Signaling Standards SupportedDevice Type Gender Typical Devices Isdn BRI Connections Asynchronous/Synchronous Serial Module Baud RatesEIA/TIA-232 Distance EIA-530 Distance Rate bps Feet Meters56-K/Switched-56-kbps DSU/CSU Connections Low-Capacitance CableOL-2171-06 Installing the Router Installing Modules, Interface Cards, and Power Supplies For network modulesFor WICs and VICs For AIMsSetting Up the Chassis Setting the Chassis on a DesktopFor internal power supplies For external power suppliesMounting the Chassis in a Rack Right To the other side of the chassis. Brackets for 19-inch rack Brackets for 19-inch rack To the other side of the chassis Attaching the Brackets to a Router of 2-RU Height Use two screws on each side For 19-inch rack Right bracketInstalling the Router in a Rack V0 ENAttaching Rubber Feet to the Router Mounting the Chassis on the WallAttaching Wall-Mount Brackets to the Router Mounting the Router on the Wall 16 Attaching the Wall-Mount BracketsInstalling the Chassis Ground Connection 17 Mounting the Chassis on the WallRing terminal Power Connections Connecting Routers to AC PowerConnecting Routers to a DC-Input Power Supply DC Wiring RequirementsRouter DC Input DC Input Wire Size1 15A, 120VAC 10A, 240VAC. StatementWiring Procedure for DC Input Connecting WAN, LAN, and Voice Cables Connecting Routers to the Cisco Redundant Power SystemPorts and Cabling Port or Connection Port Type, Color Connected To CableLAN, WAN, and Voice Connection Procedures Connecting to a Console Terminal or Modem Connecting to the Console PortConnecting to the Auxiliary Port 23 Connecting to a Console Terminal24 Connecting a Modem to the Auxiliary Port Identifying a Rollover CablePowering Up the Router Checklist for Power UpFront Panel Indicators Routers with 1-RU Chassis HeightPower-Up Procedure Routers with 2-RU Chassis HeightConfiguring the Router Initial Configuration Using SDM Initial Configuration Using the Setup Command FacilityEnter a hostname for the router this example uses Initial Configuration Using the CLI Manual Configuration Configuration is displayedTo proceed with manual configuration using the CLI, enter no OL-2171-06 Troubleshooting Isolating ProblemsTroubleshooting the Power and Cooling Systems Environmental Reporting FeaturesTroubleshooting Modules, Cables, and Connections System Messages Recovering a Lost PasswordCisco Technical Assistance Center Using the ROM Monitor Entering ROM Monitor ModeROM Monitor Commands Enter ROM Monitor Mode by Using the reload CommandROM Monitor Command Syntax Conventions Command abcRouter Management Commands ROM Monitor Command DescriptionsBoot Commands in the ROM Monitor Informational Commands in the ROM Monitor Debugging Commands Other Useful ROM Monitor CommandsConfiguration Register Commands Modifying the Configuration Register in Menu ModeRecovering Cisco IOS Software Images Modifying the Configuration Register by Hexidecimal EntryCopying an Image from the Console Using the xmodem Command Description and Options of the xmodem CommandProcedure for the xmodem Command Console RequirementsRestrictions on the tftpdnld Command Procedure for the tftpdnld Command Specify the required variables, for exampleDEFAULTGATEWAY=172.16.19.1 Bit Number Hexadecimal Meaning Configuration Register SettingsNvram Changing Configuration Register Settings Configuring the Boot Field Boot Field MeaningBit Address net host Enabling Booting from Flash Memory Baud BitOL-2171-06 Numerics IN-1Dram IN-2Isdn BRI LANLink LED IN-3Sdram IN-4IN-5 IN-6

Related manuals

Manual 14 pages 1.11 Kb

Manual 52 pages 58.61 Kb

Manual 18 pages 19.61 Kb

Manual 38 pages 43.83 Kb