Chapter 3 Installing the Router
Configuring the Router
Step 11 The configuration is displayed:
The following configuration command script was created:
hostname fig
enable secret 5 $1$D5P6$PYx41/lQIASK.HcSbfO5q1 enable password xxxxxx
line vty 0 4 password xxxxxx
snmp-server community public
!
no ip routing
!
interface FastEthernet0/0 no shutdown
media-type 100BaseX half-duplex
ip address 172.1.2.3 255.255.0.0
!
interface FastEthernet0/1 shutdown
no ip address
!
end
Step 12 Respond to the following prompts. Select [2] to save the initial configuration.:
[0]Go to the IOS command prompt without saving this config.
[1]Return back to the setup without saving this config.
[2]Save this configuration to nvram and exit.
Enter your selection [2]: 2
Building configuration...
Use the enabled mode 'configure' command to modify this configuration.
Press RETURN to get started!
Step 13 The user prompt appears:
2600>
After you complete the initial configuration tasks, your Cisco router is ready to configure for specific functions. For configuration procedures, refer to the Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers. or the Cisco IOS software configuration documentation. You can access these documents on Cisco.com and on the Documentation CD-ROM.
Initial Configuration Using the CLI (Manual Configuration)
This section shows how to bring up a command-line interface (CLI) prompt for configuration using the CLI, and it directs you to documentation for the CLI configuration.You can use the CLI if you see the following messages at the end of the startup sequence:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Cisco 2600 Series Routers Hardware Installation Guide
Cisco 2600 Series Routers Hardware Installation Guide
Corporate Headquarters
Cisco 2600 Series Routers Hardware Installation Guide
N T E N T S
Iii
Serial DTE or DCE Devices
Initial Configuration Using the Setup Command Facility
Procedure for the tftpdnld Command Configuration Register
Objectives
Vii
Conventions
Audience
Organization
Chapter Title Description
Safety Warnings
Bewaar Deze Instructies
Warnung Wichtige Sicherheitshinweise
Avvertenza Importanti Istruzioni Sulla Sicurezza
Aviso Instruções Importantes DE Segurança
Guarde Estas Instruções
GEM Disse Anvisninger
Xii
Xiii
Related Documentation
Xiv
Cisco Product Document Title
Replacement, Repair, or Refund Policy for Hardware
Cisco 90-Day Limited Hardware Warranty Terms
Duration of Hardware Warranty
Xvi
Cisco.com
Obtaining Documentation
Documentation Feedback
Ordering Documentation
Cisco Technical Support Website
Submitting a Service Request
Obtaining Technical Assistance
Xviii
Xix
Definitions of Service Request Severity
Obtaining Additional Publications and Information
Preface Obtaining Additional Publications and Information
Hardware Features
Overview of Cisco 2600 Series Routers
Advanced
Cisco
Power
Reading the Front-Panel LEDs
PWR
RPS
Activity
SYS/RPS
Reading the Rear-Panel LEDs
ACT
Cisco 2613-Rear-Panel LEDs
FDX
Link
ACT
Modules, Interface Cards, and Memory
CF1
Interface Numbering
WAN and LAN Interface Numbering
11 Interface Numbering in Chassis with 1-RU Height
Voice Interface Numbering
System Specifications
Description Specification
Regulatory Compliance
Safety Recommendations
Safety with Electricity
Preventing Electrostatic Discharge Damage
General Site Requirements
Power Supply Considerations
Power Source Input Power Tolerance Limits
Site Environment
Equipment Racks
Installation Checklist
Site Configuration
Creating a Site Log
Task Verified by Date
Tools and Equipment for Installation and Maintenance
Inspecting the Router
Console and Auxiliary Port Considerations
Console Port Connections
Preparing to Connect to a Network
Auxiliary Port Connections
Ethernet Connections
Token Ring Connections
Serial DTE or DCE Devices
Configuring Serial Connections
Serial Connections
Device Type Gender Typical Devices
Signaling Standards Supported
Distance Limitations
EIA/TIA-232
Isdn BRI Connections
Asynchronous/Synchronous Serial Module Baud Rates
Distance EIA-530 Distance Rate bps Feet Meters
56-K/Switched-56-kbps DSU/CSU Connections
Low-Capacitance Cable
OL-2171-06
Installing the Router
For WICs and VICs
Installing Modules, Interface Cards, and Power Supplies
For network modules
For AIMs
For internal power supplies
Setting Up the Chassis
Setting the Chassis on a Desktop
For external power supplies
Mounting the Chassis in a Rack
Right
To the other side of the chassis. Brackets for 19-inch rack
Brackets for 19-inch rack
To the other side of the chassis
Attaching the Brackets to a Router of 2-RU Height
Use two screws on each side For 19-inch rack Right bracket
Installing the Router in a Rack
V0 EN
Attaching Wall-Mount Brackets to the Router
Mounting the Chassis on the Wall
Attaching Rubber Feet to the Router
Mounting the Router on the Wall
16 Attaching the Wall-Mount Brackets
Installing the Chassis Ground Connection
17 Mounting the Chassis on the Wall
Ring terminal
Power Connections
Connecting Routers to AC Power
Router DC Input DC Input Wire Size1
Connecting Routers to a DC-Input Power Supply
DC Wiring Requirements
15A, 120VAC 10A, 240VAC. Statement
Wiring Procedure for DC Input
Ports and Cabling
Connecting WAN, LAN, and Voice Cables
Connecting Routers to the Cisco Redundant Power System
Port or Connection Port Type, Color Connected To Cable
LAN, WAN, and Voice Connection Procedures
Connecting to a Console Terminal or Modem
Connecting to the Console Port
Connecting to the Auxiliary Port
23 Connecting to a Console Terminal
24 Connecting a Modem to the Auxiliary Port
Identifying a Rollover Cable
Front Panel Indicators
Powering Up the Router
Checklist for Power Up
Routers with 1-RU Chassis Height
Power-Up Procedure
Routers with 2-RU Chassis Height
Configuring the Router
Initial Configuration Using SDM
Initial Configuration Using the Setup Command Facility
Enter a hostname for the router this example uses
Initial Configuration Using the CLI Manual Configuration
Configuration is displayed
To proceed with manual configuration using the CLI, enter no
OL-2171-06
Troubleshooting
Isolating Problems
Troubleshooting the Power and Cooling Systems
Environmental Reporting Features
Troubleshooting Modules, Cables, and Connections
Cisco Technical Assistance Center
Recovering a Lost Password
System Messages
Using the ROM Monitor
Entering ROM Monitor Mode
ROM Monitor Commands
Enter ROM Monitor Mode by Using the reload Command
ROM Monitor Command Syntax Conventions
Command abc
Boot Commands in the ROM Monitor
ROM Monitor Command Descriptions
Router Management Commands
Informational Commands in the ROM Monitor
Debugging Commands
Other Useful ROM Monitor Commands
Configuration Register Commands
Modifying the Configuration Register in Menu Mode
Recovering Cisco IOS Software Images
Modifying the Configuration Register by Hexidecimal Entry
Procedure for the xmodem Command
Copying an Image from the Console Using the xmodem Command
Description and Options of the xmodem Command
Console Requirements
Restrictions on the tftpdnld Command
Procedure for the tftpdnld Command
Specify the required variables, for example
DEFAULTGATEWAY=172.16.19.1
Nvram
Configuration Register Settings
Bit Number Hexadecimal Meaning
Changing Configuration Register Settings
Configuring the Boot Field
Boot Field Meaning
Bit Address net host
Enabling Booting from Flash Memory
Baud Bit
OL-2171-06
Numerics
IN-1
Dram
IN-2
Link LED
Isdn BRI
LAN
IN-3
Sdram
IN-4
IN-5
IN-6