Emulex Printer Server manual Change Port Access

Page 24

18 Command Reference Guide

Change Port Access

Specify the type of connections (access) the port can make.

>Server>> [set define change] port port_num access [dynamic local remote virtual slprt none]

port_num	Enter the port number whose access is being
	modified.
dynamic	Allows the port to originate and accept remotely-
	originated connections. This is a combination of
	remote and local access.
local	Allows a device connected to the port to
	originate connections and use the printer
	server’s local-mode command set.
remote	Restricts the port to receiving connections; it
	cannot originate connections or use any of the
	printer server’s local-mode commands. This
	type of port is typically defined as a service.
virtual	Restricts the port to usage as a transparent
	gateway.
slprt	Allows the serial port to be used as a parallel
	port on the printer server. This parallel port
	continues to accept remote LAN connections
	when the serial port is quiet.
none	Disables all access to the port.

Image 24

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide What is a Command? ConventionsFormatting You will notice text boxes labeled Note or CautionCommand Lines PromptsKeywords VariablesServer set define change server dhcp n m temp default OptionsQuotation Marks Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledHelp Initialize server delay delaymin cancel Logout port portnumPing ipaddress Test portnum count countnumCommand Reference Guide General Commands Entire command crash 300 must be entered to be effectiveDisplay Internal ARP Table Halt Printer ServerDelaymin InitializeBelow MIO Version Passwords Update Memory SyncPrivileged Access LogoutSet Privilege Password Change Login PasswordRemote Console Password PasswordNode Commands Show NodeEstablish or Change TCP/IP Nodes Show which nodes are known to the printer serverGateway FacilityDefine NetWare Node Delete NodeRemove nodes from the printer server’s internal node table NodenamePort Commands Show Port CharacteristicsDisplay the characteristics of a specified port Test PortChange Port Access Specify the type of connections access the port can makeChange Port Type Change Line Feed CharacterSpecify the type of terminal or printer connected to a port Control the line feed characterChange Port Speed Show Port Status NETJetBaudrate Server show monitor port portnum status netjet deviceServer Commands Show AlarmsShow console error conditions Define Server NameShow Server Characteristics Show Server ConfigurationDisplay Network Characteristics Show Server StatusDisplay the current configurable memory table allocation Show Server LimitsSet Console Terminal Port Enable or disable special printer server options Other OptionsAvailable options are Set Prompt Modify SnmpServer set server prompt prompt AccrightEnable or Disable Protocols Enable or disable individual protocolsProtocols Change DomainShow NetBios Characteristics AppleTalkShow Server AppleTalk AppleTalk BackspoofingShow Fonts Add Fonts AppleRemove Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Display the printer server’s LAT characteristics Change GroupsShow Server Server show list server LATNetWare Commands Define PasswordChange Authorized Groups Define NetWare NodeDisplay Characteristics Display the printer server’s Novell NetWare characteristicsChoose Frame Type Server show list server netwareServer define server netware required enabled disabled Define Required FileserverServer define node nodename nfserver Adjust Processing Speed Define as Remote PrinterRediscover Interval Server set define change server netware rediscover minutesEnable or disable the NetWare forms function Selecting Bindery Emulation or NDS ModeForms Specify the discovery method used by PserverTCP/IP Commands Specify the NDS Tree where the Pserver object existsDefine NDS Tree Change TCP/IP RoutingEstablish or Change TCP/IP Nodes BootP, Dhcp and Rarp Parameters Show TCP/IP CharacteristicsDisplay the printer server’s TCP/IP characteristics Define BootP ParametersIf both n and m are zero, Dhcp is effectively disabled Define Dhcp ParametersDefine how many times printer server will attempt Dhcp Define Rarp ParametersLoad/Dump Configuration Define TCP/IP Load HostDefine Server Load Server define server preferred load ip ipaddressPower must by cycled after this command is performed Define Software File NameSet Load/Dump Gateway Server define server software filenameServer set define change server dump enabled disabled Set Dump HostDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceDefine Service Delete ServiceShow Service