Emulex Printer Server manual Other Options, Enable or disable special printer server options

Page 30

24 Command Reference Guide

Other Options

Enable or disable special printer server options.

>Server>> [set define change] server options option_list [all enabled disabled]

option_list Enter a list of options from the available options section below.

all	Enables all options.
enabled	Adds the specified option to the existing option
	list. If not specified, the existing list is replaced
	by the new one.
disabled	Removes a specified option from the existing
	option list. The default is none -- all options
	disabled.

Available options are:

0	Enable unknown frames (bypass protocol frame
	filter).
2	Enable use of 0’s (not 1’s) in host portion of IP
	broadcast address.
3	Pack Group Codes into smallest number of bytes.
4	Host Initiated Requests announce supported
	services.
5	Print Information-Only messages to the console
	port.
6	Print Non-Fatal error messages to the console
	port.
7	Reserved.
8	Reserved.
9	Inhibit round robin port allocation.

10Enable fast TCP/IP acknowledge to speed up 38400 baud and parallel ports.

11Force an IP (or ARP) datagram to be sent out when route cannot be found.

15Enforce LAT Circuit Timer (slows performance for bridged LAT usage and prevents timeouts).

Image 30

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide Formatting What is a Command?Conventions You will notice text boxes labeled Note or CautionKeywords Command LinesPrompts VariablesServer set define change server dhcp n m temp default OptionsQuotation Marks Keyword Functions Set, Define And ChangeShow, Monitor And List Clear, Purge And DeleteCommand Summary Change node nodenam ip ipaddress tcpip gatewayEnabled disabled Ipaddr set enabled disabledPing ipaddress Help Initialize server delay delaymin cancelLogout port portnum Test portnum count countnumCommand Reference Guide Display Internal ARP Table General CommandsEntire command crash 300 must be entered to be effective Halt Printer ServerDelaymin InitializeBelow MIO Version Privileged Access PasswordsUpdate Memory Sync LogoutRemote Console Password Set Privilege PasswordChange Login Password PasswordEstablish or Change TCP/IP Nodes Node CommandsShow Node Show which nodes are known to the printer serverGateway FacilityRemove nodes from the printer server’s internal node table Define NetWare NodeDelete Node NodenameDisplay the characteristics of a specified port Port CommandsShow Port Characteristics Test PortChange Port Access Specify the type of connections access the port can makeSpecify the type of terminal or printer connected to a port Change Port TypeChange Line Feed Character Control the line feed characterBaudrate Change Port SpeedShow Port Status NETJet Server show monitor port portnum status netjet deviceShow console error conditions Server CommandsShow Alarms Define Server NameDisplay Network Characteristics Show Server CharacteristicsShow Server Configuration Show Server StatusDisplay the current configurable memory table allocation Show Server LimitsSet Console Terminal Port Enable or disable special printer server options Other OptionsAvailable options are Server set server prompt prompt Set PromptModify Snmp AccrightProtocols Enable or Disable ProtocolsEnable or disable individual protocols Change DomainShow Server AppleTalk Show NetBios CharacteristicsAppleTalk AppleTalk BackspoofingRemove Fonts Apple Show FontsAdd Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Show Server Display the printer server’s LAT characteristicsChange Groups Server show list server LATChange Authorized Groups NetWare CommandsDefine Password Define NetWare NodeChoose Frame Type Display CharacteristicsDisplay the printer server’s Novell NetWare characteristics Server show list server netwareServer define server netware required enabled disabled Define Required FileserverServer define node nodename nfserver Rediscover Interval Adjust Processing SpeedDefine as Remote Printer Server set define change server netware rediscover minutesForms Enable or disable the NetWare forms functionSelecting Bindery Emulation or NDS Mode Specify the discovery method used by PserverDefine NDS Tree TCP/IP CommandsSpecify the NDS Tree where the Pserver object exists Change TCP/IP RoutingEstablish or Change TCP/IP Nodes Display the printer server’s TCP/IP characteristics BootP, Dhcp and Rarp ParametersShow TCP/IP Characteristics Define BootP ParametersDefine how many times printer server will attempt Dhcp If both n and m are zero, Dhcp is effectively disabledDefine Dhcp Parameters Define Rarp ParametersDefine Server Load Load/Dump ConfigurationDefine TCP/IP Load Host Server define server preferred load ip ipaddressSet Load/Dump Gateway Power must by cycled after this command is performedDefine Software File Name Server define server software filenameServer set define change server dump enabled disabled Set Dump HostDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Service Commands Change ServiceDefine Service Delete ServiceShow Service