Emulex Printer Server manual Change Port Type, Change Line Feed Character

Page 25

Command Reference Guide 19

Change Port Type

Specify the type of terminal or printer connected to a port.

>Server>> [set define change] port port_num type [ansi hardcopy softcopy]

port_num	Enter the port number.
ansi	Specifies an ANSI-compatible terminal.
hardcopy	Specifies hardcopy serial terminal like a
	teleprinter with a keyboard.
softcopy	Specifies a generic video display terminal.

Change Line Feed Character

Control the line feed character.

>Server>> [set define change] port port_num mapcrlf [enabled disabled]

port_num	List of ports to be affected by the command
	separated by commas.
enabled	Removes the line-feed (LF) character from the
	carriage-return (CR) sequence.
disabled	Allows the line feed character to remain with the
	carriage return sequence.

This command is used in some Telnet session environments to strip the LF character. The printer server terminates its commands with CR. The LF character will inhibit the privileged password on the printer server, making it invalid.

Image 25

Contents Printer Server Command Reference Guide Following are trademark acknowledgments Table of Contents Ii Command Reference Guide Table of Contents Iv Command Reference Guide Conventions What is a Command?Formatting You will notice text boxes labeled Note or CautionPrompts Command LinesKeywords VariablesOptions Server set define change server dhcp n m temp defaultQuotation Marks Set, Define And Change Keyword FunctionsClear, Purge And Delete Show, Monitor And ListChange node nodenam ip ipaddress tcpip gateway Command SummaryIpaddr set enabled disabled Enabled disabledLogout port portnum Help Initialize server delay delaymin cancelPing ipaddress Test portnum count countnumCommand Reference Guide Entire command crash 300 must be entered to be effective General CommandsDisplay Internal ARP Table Halt Printer ServerInitialize DelayminBelow MIO Version Update Memory Sync PasswordsPrivileged Access LogoutChange Login Password Set Privilege PasswordRemote Console Password PasswordShow Node Node CommandsEstablish or Change TCP/IP Nodes Show which nodes are known to the printer serverFacility GatewayDelete Node Define NetWare NodeRemove nodes from the printer server’s internal node table NodenameShow Port Characteristics Port CommandsDisplay the characteristics of a specified port Test PortSpecify the type of connections access the port can make Change Port AccessChange Line Feed Character Change Port TypeSpecify the type of terminal or printer connected to a port Control the line feed characterShow Port Status NETJet Change Port SpeedBaudrate Server show monitor port portnum status netjet deviceShow Alarms Server CommandsShow console error conditions Define Server NameShow Server Configuration Show Server CharacteristicsDisplay Network Characteristics Show Server StatusShow Server Limits Display the current configurable memory table allocationSet Console Terminal Port Other Options Enable or disable special printer server optionsAvailable options are Modify Snmp Set PromptServer set server prompt prompt AccrightEnable or disable individual protocols Enable or Disable ProtocolsProtocols Change DomainAppleTalk Show NetBios CharacteristicsShow Server AppleTalk AppleTalk BackspoofingAdd Fonts Apple Show FontsRemove Fonts Apple Server show list port portnum fontsServer change port 1 fonts remove a Change Groups Display the printer server’s LAT characteristicsShow Server Server show list server LATDefine Password NetWare CommandsChange Authorized Groups Define NetWare NodeDisplay the printer server’s Novell NetWare characteristics Display CharacteristicsChoose Frame Type Server show list server netwareDefine Required Fileserver Server define server netware required enabled disabledServer define node nodename nfserver Define as Remote Printer Adjust Processing SpeedRediscover Interval Server set define change server netware rediscover minutesSelecting Bindery Emulation or NDS Mode Enable or disable the NetWare forms functionForms Specify the discovery method used by PserverSpecify the NDS Tree where the Pserver object exists TCP/IP CommandsDefine NDS Tree Change TCP/IP RoutingEstablish or Change TCP/IP Nodes Show TCP/IP Characteristics BootP, Dhcp and Rarp ParametersDisplay the printer server’s TCP/IP characteristics Define BootP ParametersDefine Dhcp Parameters If both n and m are zero, Dhcp is effectively disabledDefine how many times printer server will attempt Dhcp Define Rarp ParametersDefine TCP/IP Load Host Load/Dump ConfigurationDefine Server Load Server define server preferred load ip ipaddressDefine Software File Name Power must by cycled after this command is performedSet Load/Dump Gateway Server define server software filenameSet Dump Host Server set define change server dump enabled disabledDefine TCP/IP Dump Host Server define server preferred dump ip ipaddress Change Service Service CommandsDelete Service Define ServiceShow Service